Critically appraise and formulate engineering problems

Assignment Help Other Engineering
Reference no: EM133625756

ADVANCED ENGINEERING SCIENCE

Report - Linear and Non-linear Behaviour

Elastic critical lateral torsional buckling and post-buckling non-linear behaviour of steel girders

Objectives:
To demonstrate appropriate understanding, application and limitations of the proposed procedure for design of steel structural members subjected to destabilising effects, in particular lateral torsional buckling.

To establish a procedure using FE to determine the Elastic Buckling Moment Mcr for various support conditions and geometric properties.

To investigate the non-linear behaviour (both geometry and material non-linearity) for elements subjected to lateral torsional buckling

Analysis and Design Requirements
You are required to determine the bending design buckling resistance of a steel bridge girder, Mb,Rd in the bare-steel stage (construction stage). The girder is simply supported for in-plane bending with torsional restraint at both ends. The girder is assumed to carry a vertical udl. The data shown in Tables 1&2 provide the individualised parameters for each student.

Critically discuss and provide a concise correctly referenced summary of the available procedures for determining the Critical Buckling Moment, Mcr , and the ultimate bending resistance capacity of the steel girders referring to published literature and codes of practice. Please use APA referencing system.

Discuss how the value of Mcr is used according to the procedure in BS EN1993 to determine the design buckling moment resistance, Mb,Rd.

Determine, using Finite Elements Method, the Elastic Critical Buckling Moment, Mcr, for the bridge girder given in the Data section below. Clearly present the deformed buckled shape and clearly state the value of the uniformly distributed load (udl) at the point of buckling instability. Verify the value of Mcr using a formula from the published literature.

Carry-out, and critically discuss, the following analyses on the bridge girder in question, using Finite Elements Method.

First Order Elastic Analysis

First Order Plastic Analysis (Material Non-Linearity-MNL)

Second-order Plastic analysis (Geometric and Material Non-linearity, GNL and MNL)

Assume and justify appropriate initial distortion (imperfections). Assume and justify appropriate steel material model. Present clearly the load-deflection behaviour during load increments to clearly establish the bending resistance capacity.

Critically discuss how web stiffeners and bracing systems are used in practice when designing steel girders. Examples of bracing systems are shown in Fig.3.

Learning outcome 1: Critically appraise and formulate engineering problems.

Learning outcome 2: Evaluate solutions for engineering problems by using constitutive relationships and material failure theorems.

Learning outcome 3: Formulate, predict and test behaviour of Structures using a commercial FEM package.

Learning outcome 4: Assess and evaluate the results from the computer analysis.

Attachment:- Advanced_Engineering_Science.rar

Reference no: EM133625756

Questions Cloud

Describe all step taken in autopsy to create forensic system : Write a report for the team of investigators by doing the following: Describe all steps taken in Autopsy to create the forensic system case file.
Determine etiology of any cardiac or respiratory problems : Determine the etiology of any cardiac or respiratory problems. Describe the essential actions required to stop the dysfunction and enhance your health.
What potential problems might the ceo want to consider : What potential problems might the CEO want to consider? What steps could the CEO take to address these problems?
Registered nurses and practical nurses : A nurse working in a rehabilitation center interacts with registered nurses (RN) and practical nurses ( PN).
Critically appraise and formulate engineering problems : M26323 ADVANCED ENGINEERING SCIENCE - University of Portsmouth, Evaluate solutions for engineering problems by using constitutive relationships
Discuss why are collisions bad to message integrity : When this happens, we refer to the event as a "collision". In this paper, you are going to discuss why are collisions bad to message integrity.
Alternative medicines and treatments in any psychotherapy : This can include alternative medicines and treatments in any psychotherapy. Provide a pharmaceutical based therapy for this patient.
Differences between theodor adorno and colleagues : What are the similarities and differences between Theodor Adorno and colleagues (1950) and Billig 1995 in their concepts.
What is the difference between an ids and an ips : What is the difference between an IDS and an IPS? Why is it important to perform a network traffic baseline definition analysis?

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd