Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a) create a 512-length signal by using the rand command, then low-pass filter the signal with the filter h=1/2[1 1] to bandlimit the function, which can be represented with by the command filter.m with b1=b2=1/2, and a1=1b) Upsample the filtered signal x[n] by a factor of 2 to produce v[n] and display it frequency response (length 1024). Describe |V()| and compar it with |X()|.
c) Design an interpolation filter f[n] for v[n]. Computer y[n]=v[n]*f[n]. Graph y[n] and v[n] on the same plot and verify that y[2n]=v[2n].
d) Plot |V()| and |Y()| and describe their relation.
e) Find y1[n]=(2)(3) x[n] and y2[n]=(3)(2) x[n], and verify that y1[n]=y2[n]
There are to be 15 states, and the device for utilization is a 22v10 chip using 8 flip flops internal to the device. The outputs are 8 LEDs and a secondary output Z that is a 1 if states 10,11,12,13 are active.
An ignition coil has an inductance of 1.75 henrys and an internal resistance of 6 ohms. It is connected to a 13.5 volt automotive DC source. The switching opening speed of the points is 0.17 milliseconds
A DC motor is driving a load given by TL = 2 + 0.02ωL Nm , where ωL is the speed in rad/sec. The armature resistance of the motor, Ra = 2Ω . The machine constants, kE=kT =0.4 (in SI units).
Select the appropriate resistor to add to the circuit in order to reduce the voltage across the bulb to the appropriate level. Choose the nearest 10-% resistor value and determine what its power rating should be.
The battery voltage is 20V Resistor3 a resistance of 20ohms. Resistor1 has a resistance of 30. Current flow is 250mA through the circuit. What is the resistance of resistor 3
In an electricity experiment, it was observed that as the potential difference in volts across a thin platinum wire increases the current in amperes changes as follows: (V,I)=(0,0), (1.0,0.112), (3.0,0.337), and (6.1,0.675).
A charge Q is placed on each sphere> the electric force of repulsion separates the spheres, and an equilibrium is reached when the suspending threads make an angle of 10 degrees. Assuming a gravitational force of 9.80(N/kg) and a negligible mass f..
The input capture option on the HCS12 is used to measure the period of a 100 Hz signal. With an E-clock of 24 MHz and no scaling, how many overflows will occur Assume the free-running timer starts at 0x0000.
Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the following motor control specifications:1) A motor must be started and stopped from any one of three start/stop pushbotton stations.
At a certain location, the horizontal component of the earth's magnetic field is 3.70 10-5 T, due north. A proton moves eastward with just the right speed for the magnetic force on it to balance its weight. Find the speed of the proton.
Three series-connected capacitors, C1, C2 and C3, with capacitances 10uF, 15uF and 27uF respectively, are connected in parallel with a 15uF capacitor and a 150V DC source. Calculate: a) Equivalent capacitance of the circuit
(a) What is the acceleration of an electron in a uniform electric field of 1.0x106 N/C (b) How long would it take for the electron, starting from rest, to attain one-tenth the speed of light. Assume that Newtonian mechanics holds.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd