Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Contrast the electron and hole drift velocities through a 10 um (micro meter) layer of intrinsic silicon across which a voltage of 5V is imposed. Let up = 480cm2/Vs and un=1350cm2/Vs.
Convert the following differential equation 5 (t) +4 (t) +3x.(t) + 2x(t) + 7u(t) - 5u.(t) + 2 (t) = 0 to state space form. Is this system marginally stable, asymptotically stable, or unstable when u(t) = 0 Determine stability by using the state sp..
find the fourier series coefficients of z(t) (use the results of a) and b) along with the multiplication property of continuous time fourier series coefficients). find the fourier series coefficients of z(t) through direct expansion of z(t) in tri..
Assume the phone to be hand-held(i.e no pencil -beam emitted, fold-out antennas might be an option) and a LEP (low earth orbit) satellite at a height of 780KM. Keep in mind that a LEO satellite is moving with respect to earth's surface. Pick state..
A 10 cm length of a K-band copper waveguide is filled with a dielectric material with er = 2.55 and tan f = 0.0015. If the operating frequency is 15 GHz, find the total loss through the guide and the phase delay from the input to the output of th..
Light traveling in air strikes a glass plate at an angle θ1 = 33 degrees, where θ1 is measured between the incoming ray and the glass surface. Upon striking the glass, part of the beam is reflected and part is refracted.
if we have a circuit with R= 5, L=22mH, C=22nF , Vs=10 and the switch S was opens for a long time and it closes at time t=0 second. all connected in series, how can i find the voltage in the capacitor Vc
Design a Miller integrator with a time constant of 0.1 s and an input resistance of 100 k ohm. A dc voltage of -1 volt is applied at the input at time 0, at which moment vO = -10 V. How long does it take the output to reach 0 V to +10 V
Assume that we have an image represents a sinusoidal variation orthogonal to the x-axis with amplitude of 10 and period of 1 cm, that repeats infinitely in all directions within the plane. Further assume an average intensity of 10.
A voltage source with voltage Vs = V0 sin(pi*t) is driving a load of RL = 100 Ohms. The load is connected to the source by a transmission line with characteristic impedance Z0 = 50 Ohms. The velocity of propagation on the line is 2 108 m/s.
A linear time-invariant system is described by the difference equation y[n]=x[n]+x[n-4] (a) Find its impulse response h[n]. (b) Find its system function H(z). (c) Plot the poles and zeros of H(z) in the z-plane.
The probe band limited signal with fmax= 1Mhz was transmitted during the time T0=2 minutes. a) Find the maximum number of samples (N) that can be sent through the channel during T0 without losing of information. b) Find the sample rate (samples/s)
A balanced three-phase inductive load is supplied in steady state by a balanced three-phase voltage source with a phase voltage of 120 V rms. The load draws a total of 10 kW at a power factor of 0.85. Calculate the rms value of the phase currents
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd