Construct a timer program that will operate a lamp

Assignment Help Other Engineering
Reference no: EM131060573

Electronic Systems Engineering Assignments-

Assignment 1-

1) Develop a simple ladder logic program that will turn on an output X if inputs A and B, or input C, or input D is on. All inputs (A, B, C and D) and the output (X) are external to the systems. You are required to use proper addresses for the inputs and the output.

2) An operation requires timing a long period of 18 hours. Construct a timer program that will operate a lamp once the period has elapsed. A manual push button is used to reset the process. [Note: Make sure that you use values which are not out of range.]

3) Note: The following two questions are practice problems (#17 and # 18 of Chapter 08 in the Hugh Jack book (Automating Manufacturing Systems with PLCs). Solutions using the Allen Bradley counters and timer instructions are provided in the book. Repeat these problems using the Omron PLC instructions.

a) Design a conveyor control system that follows the design guidelines below.

i) The conveyor has an optical sensor S1 that detects boxes entering a workcell

ii) There is also an optical sensor S2 that detects boxes leaving the workcell

iii) The boxes enter the workcell on a conveyor controlled by output C1

iv) The boxes exit the workcell on a conveyor controlled by output C2

v) The controller must keep a running count of boxes using the entry and exit sensors

vi) If there are more than five boxes in the workcell the entry conveyor will stop

vii)If there are no boxes in the workcell the exit conveyor will be turned off

viii) If the entry conveyor has been stopped for more than 30 seconds the count will be reset to zero, assuming that the boxes in the workcell were scrapped.

b) Write a ladder logic program that does what is described below.

i) When button A is pushed, a light will flash for 5 seconds.

ii) The flashing light will be on for 0.25 sec and off for 0.75 sec.

iii) If button A has been pushed 10 times the light will not flash until the system is reset.

iv) The system can be reset by pressing button B

4) Write a program that will use timer (s) to flash a light. The light should be on for 2.0 seconds and off for 0.25 seconds. Do not include start or stop buttons.

5) A high-speed machine requires the number of parts to be counted before changing the dies for the next part. The number of parts is 52,200. Construct a counter program that will operate a buzzer and stop the process when the number of parts is reached. A manual reset is required.

Assignment 2-

Q.1- (a) Find energy of the signals plotted in Figure 1. Note that amplitudes are only non-zero for 0 ≤ t ≤ 4.

(b) Find the correlation coefficient ρ between the pulse x(t) and the pulses yj(t), j = 1, 2, 3.

1673_Figure.png

Q.2- A signal composed of sinusoids is given by the following equation:

x(t) = 4 + 3cos (250 πt+ (π/4)) + 4sin (500 πt)

(a) Determine the angular frequency (ω0), time period (To), and the coefficients in the following representations:

Compact Trigonometric Fourier series: x(t) = c0 + n=1Σcn cos(n ω0 t + θn)                               

Exponential Fourier series: x(t) = n=-∞ΣDnejnw0t

(b) Sketch the single-sided as well as two-sided spectra of x(t) indicating the magnitude and phase of each frequency component. Which harmonics are present in x(t)?

(c) Consider a new signal y(t) = x(t) 2cos (50 πt - (π/3)). How is the two-sided spectrum changed? Is y(t) periodic? If so, what is the period?

Q.3- Magnitude and phase spectra of a composite signal g(t) are shown in Figure 2.

2007_Figure1.png

(a) Write an equation for g(t) in terms of cosine functions.

(b) Is g(t) periodic? Explain why or why not. If its periodic, what is the fundamental frequency (f0) and corresponding period (T0) of g(t)?

(c) Consider a new signal h(t) = 10cos(2παt + π) + g(t). Assuming h(t) is a periodic with period T0 = 0.01 sec, determine positive values for the frequency α that will satisfy the condition.

(d) Use any of the values for the frequency α obtained in (c) to modify the spectra of Figure 2.

Q.4- Magnitude and phase spectra of a composite signal z(t) are shown in Figure 3

175_Figure2.png

(a) What is the maximum frequency present in z(t)?

(b) What is the fundamental frequency (f0) and time period (T0) of z(t)?

(c) What is the minimum sampling rate required to recover the original signal back?

(d) Assuming that z(t) is sampled at a rate of 1900 Hz, can we reconstruct the signal from the digital version?

(e) Use Parseval's theorem to find the power of z(t)?

Q.5- Given is the Fourier transform of x(t):

x(f) = j2πf/1+j2πf

Use table of the Fourier Transforms to find Y(f) of the following signals:

(a) y(t) = x(t/2 + 1)

(b) y(t) = (-10Cos(200πt))x(t+1)

(c) y(t) = ¼ dx(t)/dt

(d) y(t) = -∞t x(τ).dτ

Reference no: EM131060573

Questions Cloud

What is the encryption of m=34 : What is theencryption of m=34?
Write an essay about mans voyage to mid-life- crisis : Write an essay about Man's Voyage to Mid-Life - Crisis?
Problem of involuntary unemployment : According to classical economists, wage cut was viewed as the best policy to solve the problem of involuntary unemployment. However, Keynes denounced the classical notion. On what grounds did Keynes base his arguments?
What is meant by like or similar terms : Describe how binomials are multiplied and provide an example of your own. What is meant by "like" or "similar" terms? How does this concept relate to adding and subtracting polynomials.
Construct a timer program that will operate a lamp : An operation requires timing a long period of 18 hours. Construct a timer program that will operate a lamp once the period has elapsed
Calculate the departmental overhead rate : Handy Display Company manufactures display cases to be sold to retail stores. The cases come in three sizes: large, medium, and small. Calculate the departmental overhead rate for each of the three departments listed.
Write code to complete printfactorial()''s recursive case : Write code to complete PrintFactorial()'s recursive case. Sample output if userVal is 5:
Assuming no personal taxes on debt or equity income : The unlevered firm expects to earn $250,000 in net operating income each year for the foreseeable future. It has a tax rate of 40% and has a capitalization rate of 8% equal to the industry required return for this type of firm. what is the overall va..
Write an algorithm that takes two line segments as input : Write an algorithm that takes two line segments as input (specified by the end points) and outputs true if the segments intersect and false otherwise.

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd