Compute the work done by the gas for the processes

Assignment Help Civil Engineering
Reference no: EM13319562

Two pounds of an ideal gas are contained within a piston-cylinder arrangement. The initial volume and pressure are 1 ft3 and 75 psia respectively. The final volume is 3 ft3. compute the work done by the gas for the following processes: (a) constant pressure, (b) constant temperature.

Reference no: EM13319562

Questions Cloud

What is the estimated collection efficiency at 250degree f : Our ESP is collecting 95% of the particles in our exhaust stream. We are under pressure to improve its performance. It has been suggested that if we were to cool the inlet gas from the present 600°F to 250°F
Explain ammonium sulfate-((nh4)2so4) : If the following substance is dissolved in pure water, will the solution be acidic and Explain Ammonium sulfate-((NH4)2SO4)
Determine the rate at which heat must be transferred : A 50-ohm electrical resistor carries a current of 5 amperes. The resistor is maintained at a temperature of 30o C. Determine the rate at which heat must be transferred to the surroundings
How fast is it going at the bottom of the ramp : A ball is at the top of a ramp that is 4.5 m above a table. If the ball rolls without friction, how fast is it going at the bottom of the ramp
Compute the work done by the gas for the processes : Two pounds of an ideal gas are contained within a piston-cylinder arrangement. The initial volume and pressure are 1 ft3 and 75 psia respectively. The final volume is 3 ft3.
What is this manufacturer fixed cost : For each level of output, calculate the variable cost (VC). For each level of output except zero output, calculate the average variable cost (AVC), average total cost (ATC), and average fixed cost (AFC). What is the minimum-cost output?
How far does the car travel : A car uniformly decelerates at a rate of -5.00 m/s^2. How far does the car travel after 1.5 seconds if it initially was moving at a speed of 25 m/s
Determine the temperature after throttling : Wet steam at a pressure of 1382 kPa and a quality of 99% is throttled to a pressure of 689.5 kPA. Find the temperature after throttling.
Explain a solute is always molecules dissolved in water : Which of the following statements is/are correct. a) Water is an example of non-polar solvent. b) Any solution always conatins an electrolyte c) NONE d) A solute is always molecules dissolved in water and cannot be ions.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine factor of safety of trench by the culmann method

A 1.5 meter deep vertical wall trench is to be cut in a soil whose unit weight is 17.36 kN/cubic meters, angle of internal friction is 25 degrees, and cohesion is 20.6 kN/square meters.

  Find the work done in pumping the water

a horizontal cylindrical tank 4 ft in diameter and 10 ft long is full of water. find the work done in pumping the water to a point 4 above the top of the tank.

  Determine the magnitude of the velocity and acceleration

If the blades are originally at rest and begin to turn with a constant angular acceleration of ac = 0.5 rad/s^2, determine the magnitude of the velocity and acceleration of points A and B on the blade when t = 4s.

  What are the effects of degree of hydration on capillary

What are the effects of degree of hydration on capillary pore volume, capillary pore size, porosity, permeability, and compressive strength of hydrated cement (Degree of hydration: hydrated cement/total cement, increases with time and temperature)

  How are compacted and loose bulk density used in real life

How are compacted and loose bulk density used in real life. Also is a high degree of accuracy necessary in the bulk density tests

  How many pounds of bod are destroyed by the plant each day

A wastewater treatment plant produces 34, 500 pounds of secondary sludge each day. Wastewater flows into the plant at a rate of 5.6 MGD and has an influent BOD of 325 mg/L. How many pounds of BOD are destroyed by this plant each day

  Calculate the partial pressure exerted by each gas

A 30-liter volume of gas at 25 degrees C contains 12 g of methane (CH4), 1 g of nitrogen (N2), and 15 g of carbon dioxide (CO2). Calculate (a) the moles of each gas present, (b) the partial pressure exerted by each gas, and (c) the total pressure ..

  What is significant difference between free jets and flows

What is the most significant difference between "free" jets and flows in confined structures (nozzles, pipes, etc.) in terms of formulation of force terms ÓF(i.e. left hand side) of the momentum equation

  Determine the seepage velocity of water through aquifer

a) Calculate Darcy's velocity of the groundowater as well as the amount of water that passes through the aquifer each day. b) for the same aquifer, determine the seepage velocity of water through aquifer if the effective porosity is 32%.

  Give an equation for relative uncertainty of head loss

Equation for head loss in a pipe when it is laminar flow: head loss, h= (32*dynamic viscosity,u*pipe length,L*average velocity of fluid,V) / (gravitational acceleration,g*pipe diameter,D^2) Give an equation for relative uncertainty of head loss

  Calculate manning coefficient n for the given reach

The following data are obtained for a particular reach of the Provo river in Utah: cross sectional area A = 183 ft2, free surface width = 55 ft, average depth = 3.3 ft, Rh = 3.32 ft, V = 6.56 ft/s, length of the reach = 116 ft, and elevation drop ..

  Estimate the actual population contributing flow to the main

What is the maximum population that can be served by a 900 mm diameter main sewer constructed on minimum grade. If sewage flow in the pipe never exceeds a depth of 600 mm, estimate the actual population contributing flow to the main.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd