Compute the displacement of the car between 2.0s and 3.8s

Assignment Help Civil Engineering
Reference no: EM13557018

The position of a car traveling between two stop signs along a straight city block is given by r=[9t-(43/2)sin(2t/5)]m, where t denotes time and 0s<t<17.2s (signs should be less than or equal to). Compute the displacement of the car between 2.0s and 3.8s as well as between 11.1s and 12.6s. For each of these time intervals compute the average velocity.

change in r1=?

change in r2=?

Vavg of 1=?

Vavg of 2=?

Reference no: EM13557018

Questions Cloud

Find the angle between the electric field and axiz of filter : Only 25% of the intensity of a polarized light wave passes through a polarizing filter. What is the angle between the electric field and the axiz of the filter
Compute the tension of the wire : A wire with mass 85.0 is stretched so that its ends are tied down at points 82.0 apart. Compute the tension of the wire
Find the magnitude of the maximum acceleration of the glider : One end of a stretched ideal spring is attached to an airtrack and the other is attached to a glider with a mass of 0.360. Find the magnitude of the maximum acceleration of the glider
What is the cutoff wavelength of the x-rays : A tungsten (W) target is bombarded by electrons accelerated through a potential of 60 kV. What is the cutoff wavelength of the X-rays emitted from the target
Compute the displacement of the car between 2.0s and 3.8s : The position of a car traveling between two stop signs along a straight city block is given by r=[9t-(43/2)sin(2t/5)]m, where t denotes time and 0s
What is the minimum perimeter of that the blade must have : A rectangular blade weighing 0.02 lbf is kept in the surface of water (sigma=0.073 N/m) solely by surface tension forces. What is the minimum perimeter of that the blade must have so that this is possible
Determine the minimum force p to prevent a 30kg rod ab from : Determine the minimum force P to prevent a 30kg rod AB from sliding on a wall. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is Us=0.2.
Find the cross sectional area of constricted portion of pipe : Water enters a pipe with a cross sectional area of 3.0 cm2 with a velocity of 3.0 m/s. What is the cross sectional area of the constricted portion of the pipe
Determine the minimum required dimension for t so that : The wood specimen is to be loaded in a testing machine until it fails in tension. The ultimate normal strength of the wood is ?ult = 1800 psi and the ultimate shear strength of the wood is ult = 800 psi.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine true coefficient of discharge in the weir equation

A rectangular channel carries a discharge of 2.00 m3/sec per meter of channel width over a weir crest that is 1.4 m in height. The energy grade line upstream of the weir measure 2.7 m above the channel bottom

  Why its necessary to require conditions-sand cement ratio

Why is it necessary to require such conditions-sand cement ratio, w/c ratio and type of sand. A graded sand is specified for use in the mortar cube test. What would be the likely results if a one-sized sand was used instead of a graded sand.

  Effective vertical stresses of the clay layer

The saturated unit weight of the clay is 20kN/m 3 and that of the sand 19 kN/m 3 ; above the water table the unit weight of the sand is 16.5 kN/m 3 . Calculate the effective vertical stresses at the top and bottom of the clay layer.

  Determine the pressure that develops in the container

A rigid-walled cubical container is completely filled with water at 40 0F and sealed. The water is then heated to 100 0F. Determine the pressure that develops in the container when the water reaches this higher temperature

  What is the solids concentration of primary clarifier sludge

A 20 mgd wastewater treatment plants primary clarifier influent has 800 mg/l solids. the clarifier removes 18 percent of the solids. the sludge flow rate is 0.070 MGD.

  Determine what is the force acting on the plunger

A plunger applies pressure to the water. If, with zero force, the initial length of the water column is 25.00 in, what will it's length be if a force of 420lbs is applied to the plunger. Assume no leakage and no friction.

  Determine the peak outflow rate

Determine the peak outflow rate when the inflow hydrograph is routed through this basin and what is the design storage and water surface elevation at the peak outflow rate.

  Determine force p required to move wedge under the post

Determine the force P required to move the wedge under the post. The coefficient of static friction between all surfaces is 0.25. The applied force F is 200 lbs and the angle alpha is 15 degrees.

  How many square inches of coating need to be applied

Workers plan to apply a reflective coating of paint to one surface of an equilateral triangular shaped highway sign. How many square inches of coating need to be applied to the sign if one side of the triangle is 12 inches

  Calculate the fraction of vocs in the exhaust

For a circular concrete column in a building with a diameter of 12" and subjected to an axial load of 200 kips, determine the stress exerted on the x-section of that column. What type of stress would it be?

  How to determine the height of the building in feet

The basic barometer can be used to measure the height of abuilding. If the barometric readings at the top and at the bottomof a building are 28.7 and 29.7 in Hg, respectively, determine the height of the building in feet.

  What is the probability there will be at least one call

The number of telephone call coming in the business switchboard average 4 minutes/call. Let x be the number of calls received, Poisson variable. a. What is the probability there will be at least one call in a given one minute period.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd