User Account

All Pages

Compute power and the power factor for the total load

Assignment Help Electrical Engineering
Reference no: EM13266473

The load on a 460-v, 60-Hz, Y-connected, balanced three phase source consists of three equal Y connected impedance of 100-j100 Ohms and three equal delta-connected impedance of 300-j300 Ohms. Compute the line current, power, and the power factor for the total load.

Reference no: EM13266473

Questions Cloud

How many moles n have been introduced into the bag : The pressure of the gas within the bag remains at 1 atm and its temperature remains at room temperature 20.0 Celsius. How many moles 'n' have been introduced into the bag by the time its volume reaches 22.4 L
Determine what is the value of theta in degree : Given f1(t) = 28.2843 cos ( 100t - 30) and f2(t) = 14.1421 sin (100t + 15), what's the phasor value of f1(t), F1 and f2(t), F2 The sum of f1(t) and f(2)t is f3(t), where f3(t) = Fm cos(100t - theta)
Explain what will be the percent relative error : a method for the determination of copper yields results that are too low by 0.47mg. What will be the percent relative error due to this source if the weight copper in a sample is 45.3 mg
Find the change in entropy of the air : A 72.0-kg log falls from a height of 20.0 m into a lake. find the change in entropy of the air during this process
Compute power and the power factor for the total load : The load on a 460-v, 60-Hz, Y-connected, balanced three phase source consists of three equal Y connected impedance of 100-j100 Ohms and three equal delta-connected impedance of 300-j300 Ohms.
State the dry solute and the solvent : How much dry solute would you take to prepare each of the following solutions from the dry solute and the solvent?
Determine the useful power output of the heat engine : A Carnot engine uses a steam boiler at 100°C as the high-temperature reservoir. Determine the useful power output of the heat engine
What is the current of circuit in frequency and time domain : A series circuit has a resistance of 1 ohm and an inductance of 1 ohm. The voltage across the circuit has an amplitude of 15 volts and a phase shift of 30 degrees. What is the current of the circuit in frequency and time domain
Define what is the molar concentration : What is the molar concentration of 2.0 grams of sodium chloride brought to 0.25 L using water

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design a double sideband amplitude modulation modulator

Design a Double Sideband Amplitude Modulation (DSBAM) modulator and demodulator system using the SystemView software. The modulating wave m(t) = Amcos(2pifmt) and the carrier wave c(t) = Accos(2?fct) have the following parameters

  What is corresponding change in the regulated output voltage

A shunt regulator utilizing a zener diode with an incremental resistance of 5ohm is fed through an 82ohm resistor. If the raw supply changes by 1.0V, what is the corresponding change in the regulated output voltage

  Determine average power lost in propagating across surface

A 1 Ghz, 1 V/m uniform plane wave is propagating in a lossy material having parameters of σ= 2 (S/m), εr= 9, and μr = 16. Determine the average power lost in propagating across a 100 cm2 surface perpendicular to it

  Explain why can discrete-time fir digital filters

Why Can Discrete-Time FIR Digital Filters be a Linear Phase, Why can discrete-time FIR digital filters be made exactly linear phase, whereas IIR digital filters cannot?

  Find cutoff frequencies if sampling frequency in 30 khz

Sketch magnitude and phase responses (as linear gain versus digital frequencies) for each filter (use [0,π]). Indicate filter type. Find cutoff frequencies if sampling frequency in 30 kHz. Use 6 points only. Do not use MATLAB.

  Calculate the flat band potential and the threshold voltage

Calculate the FLAT BAND POTENTIAL and the THRESHOLD VOLTAGE for a real n+ polysilicon / p- silicon MOS diode having Na= 1017 cm^-3 and oxide thickness d = 5 nm. Assume that the oxide has only fixed oxide charges (Qf)

  Design a three mode pid controller

A liquid level system converts a 4-10 m level into a 4-20mA current. Design a three mode controller (PID im assuming) that outputs 0-5 volts with 50% PB, 0.03 min integration time, and 0.05 min derivative time. Fastest expected change time is 0.8 ..

  Non-feedback- four-character combinations

Assuming no feedback to the adversary until each attempt has been completed, what is the expected time to discover the correct password?

  Determine the steady state response for a step input

Are the systems stable For functions above, determine the steady state response for a step input. Determine the natural frequency , and the damping ratio and sketch the step response.

  Find the linetoneutral voltage phasors line-to-line voltage

Each phase of the load consists of an impedance of 30 + j40 *. Find the linetoneutral voltage phasors, the line-to-line voltage phasors, the line-current phasors, the power, and the reactive power delivered to the load.

  Find out the capacitance per unit length c

Cross-section of a coaxial cable:he radii of two concentric conductor is a and b respectively. In between, it is filled with an ideal dielectric with a permittivity e. Assume the charge in the inner conductor is Q Coulomb/meter.

  Solve using n rectangles and the limit process

(a)using 4 rectangles find the area of the region bounded by f(x)=x^2 +1, the axis from x=0 to x=2,(b) solve part (a) using n rectangles and the limit process as n -> infinity.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd