Compare the crystalline state in metals and polymers

Assignment Help Civil Engineering
Reference no: EM13543339

1.For cubic crystals, as values of the planar indices h, k, and l increase, does the distance between adjacent and parallel planes (i.e., the interplanar spacing) increase or decrease? Why?

2.Compare the crystalline state in metals and polymers. (b) Compare the noncrystalline state as it applies to polymers and ceramic glasses

3.Offer an explanation as to why covalently bonded materials are generally less dense than ionically or metallically bonded ones.

Reference no: EM13543339

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the normal depth using trial and error technique

For a trapezoidal shaped channel (n=0.014 and slope = 0.0002 with a 20-ft bottom width and side slopes of 1:1.5 (V:H), determine the normal depth using trial and error technique for a discharge of 1000 cfs.

  Determine the scale of the project graphically andanalytical

Assume the following equations for the total benefit and totalcost of a reservoir project as afunction of scale, Q, expressed asmillion gallons water delivered per day(MGD):

  Estimate energy release rate by using regression equation

A concrete building has floor area 10 m by 20 m and is 4 m high. THe building has four windows with a height 1.6 m and a width 2 m. After 10 minutes gases in the room have an average temperature of 700 degree Celcius.

  Determine the max rimpull of the tractor in each gear

A pneumatic-tired tractor with a 354 - hp engine has a maximum speed of 3.6 mph in 1st gear. Determine the max. rimpull of the tractor in each gear if the engine effieicency is 91%.

  Find what is the degree of saturation of the field sample

Let us pretend you are an earthwork construction control inspector and you are checking the field compaction of a layer of soil. After compaction in the field, the density of soil was checked by excavating part of the compacted soil

  Ignore emissions from manufacturing the packaging

Ignore emissions from manufacturing the packaging material

  Compute the pressure at a point in a building

A rectangular culvert 4 feet x 6 feet is running full and discharging 3,500 cfm. There is no friction loss. Find the velocity in fps. The culvert empties into a 10 ft wide culvert and the velocity reduces to 0.6 fps. How deep is the water level in th..

  Determine the nominal flextural strength of the section

a rectangular beam with a width of a 8 in. an effective depth of 10 in., and a total depth of 12 in., is reinforced with a single fiberglass reinforcing bar that has a cross sectional area of 0.45 in^2.

  Compare the head loss for water flow in a steel pipe

Compare the head loss for water flow (Q=5 cfs) in a 12 in., 3000 ft. long steel pipe using the darcy-weisbach equation and the hazen-williams formula.

  What is diameter of bubble before it reaches water support

An air bubble of .3 inch diameter is released from the regulator of a scuba diver 100ft below the waters surface. The water temp is 85 degree's F. What is the diameter of the bubble before it reaches the waters surface.

  What is the minimim required diameter d-min of the pins used

A plane truss has joint loads P, 2P, and 3P at joints D, C and B, respectively where load variable P=23kN. All members have two end plates which are pin-connected to gusset plates.

  What isthe max increase in temp if the stress in the steel

A square member is composed of a 12 inlong. 1 sq in area steel core with Young's modulus=29*10^6 psi andthermal expansion coefficient of 6.5*10^-6 /deg F

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd