User Account

All Pages

Cold cranking amperes of conventional lead-acid automobile

Assignment Help Mechanical Engineering
Reference no: EM13704640

The cold cranking amperes (CCA) of a conventional lead-acid automobile battery is the amount of current the battery can provide at 0°F for 30 seconds and maintain at least 1.2 volts per cell (or 7.2 volts for a standard 12-volt battery). If a battery is rated for 700 CCA, how much work will it deliver to the starter motor, assuming the minimum voltage (7.2 V) and maximum time (30 s) are required?

Reference no: EM13704640

Questions Cloud

Significant mass and energy flows into an out of the room : On a hot summer day, a student turns his fan on when he leaves his dorm room in the morning. The dorm is well insulated but not air conditioned, and all of the doors and windows are closed. Draw a simple picture of this room after the student leaves ..
Pump is used to raise the pressure of water : A pump is used to raise the pressure of water from 0 psig to 55 psia. How much power (in kW) will be required to pump 1.5ft3 /s of water? What is the effect of the water temperature on the pump power that is required?
Consider a micro channel with a constant voltage : An important application of micro fluidics is in the area of electro kinetic separations, in which an electric field is applied along the length of a micro channel to generate differential velocities for various components (molecules, nanoparticles, ..
Propose a reasonable synthesis of alcohol : Propose a reasonable mechanism for the reaction - Propose a reasonable synthesis of alcohol and discuss the reaction in terms of the ease of each successive step and sketch the dominant product or products of the overall reaction
Cold cranking amperes of conventional lead-acid automobile : The cold cranking amperes (CCA) of a conventional lead-acid automobile battery is the amount of current the battery can provide at 0°F for 30 seconds and maintain at least 1.2 volts per cell (or 7.2 volts for a standard 12-volt battery).
What is the value of re for the smaller channel : The Reynolds number for a particular micro channel flow is found to be Re = 2. If all channel dimensions (length, width, and height) are reduced by a factor of 10, and the time required for a particle to traverse the length of the channel is invarian..
What is the line in the new coordinate system : A line is represented by two end points (-1,0,0) and (2,0,0). The coordinate system is rotated 90 degrees about the y axis and then the orgin is moved to (2,2,2). What is the line in the new coordinate system? I need help on using this with homogeneo..
Determined the diameter for the steel rod : A machine with a mass of 5000kg will be lifted by a steel rod with an ultimate tensile strength of 860MPa. A factor of safety of 4 must be used. Determined the diameter for the steel rod
Calculate-using the psychometric equations : Calculate, using the psychometric equations presented in class, the humidity ratio, enthalpy, specific volume, and dew point of air at 27.4°C dry-bulb temperature and 43% relative humidity at standard atmospheric pressure (101.325 kPa). Verify your ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The specific internal energy in kjkg at the initial state

20 kg of water at 200 kpa with a quality 25 is heated under a constant volume process until its pressure reaches 400

  Determine the rate of entropy generation ie irreversibility

a car traveling at highway speed assume 60 miles per hour 1 mile 5280 ft must overcome a drag force of approximately

  The corresponding magnitude of r

Two control rods are attached at A to lever AB. Using trigonometry and knowing that force in the right-hand rod is F2=20 lb, determine a.) the required force F1 in the left-hand rod if the resultant R of the forces exerted by the rods on the le..

  The simple steam power cycle in prob 423 in modified in the

the simple steam power cycle in prob 4.23 in modified in the following way. steam entering the turbine is expanded to

  A rigid tank contains an ideal gas at 1227 c and 200 k pa

a rigid tank contains an ideal gas at 1227 c and 200 k pa. the gas is cooled until the gauge reads 50 k pa. if the

  Dtermine a the velocity when x 2mb the position where the

the acceleration of the particle is defined by the relation a 25-3x2 where a is expressed in msec2 and x in meters. the

  Material a has a fracture toughness and yield stress ten

material a has a fracture toughness and yield stress ten times that of material b a write an expression for the

  An oven 1300 f at a rate of 300 per min if the plates

at a production facility 1.2 in thick 2 ft x 2 ft square brass plates denisty532.5 lbmft3 and cp 0.091 btulbmf that are

  Determine the expected rating lives in hours of a 35 mm

determine the expected rating lives in hours of a 35 mm bore 02 and 03 series straight cylindrical bearings operating

  The boom derrick supports a suspended 15-kip load the

the boom derrick supports a suspended 15-kip load. the booms bc and de are each 20 ft long. the distances are a 15 ft

  Find the specific flow exergy in and out of the steam

find the specific flow exergy in and out of the steam turbine in example 9.1 assuming an ambient at 293 k. use the

  For an enlarged control volume that includes the turbine

steam enters a turbine operating at steady state at a pressure of 1000 lbfin2 and a temperature of 1100degf and exits

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd