Calculate what is the peak discharge at the reach outlet

Assignment Help Civil Engineering
Reference no: EM13316902

Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate. From past observations the time lag between peaks at the inlet and outlet of the reach is 2.5 hr, and the x coefficient is 0.35. What is the peak discharge at the reach outlet, and when does it occur?

Reference no: EM13316902

Questions Cloud

Determine the change in storage during month of september : The average flow rate of the River Tiger into the lake was determined to be 3.5 m3/s and the average flow rate of the River Yankee out of the lake was measured at 2.5 m3/s (ignore any loses due to evapotranspiration).
What is the net force on the roof : If wind blows at 32 m/s over a house, what is the net force on the roof if its area is 238 m2 and is flat
How fast does air flow in the duct : A 20 cm radius air duct is used to replenish the air of a room 9.2 m multiplied by 5.5 m multiplied by 5.0 m every 10 min. How fast does air flow in the duct
Audit risk model and discuss how they interact : Audit risk is a key consideration and guide to planning an audit - explain why and list the key components of the Audit Risk Model (ARM) and discuss how they interact?
Calculate what is the peak discharge at the reach outlet : Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate.
What is the buoyant force on the diver in sea water : A scuba diver and her gear displace a volume of 65.0 L and have a total mass of 64.0 kg. What is the buoyant force on the diver in sea water
Find a problem in managing global supply chains : MGMT 4337 - Team Case Analysis Find a problem in managing global supply chains from the real business world and identify specific SCM concepts/tools that can be applied to the problem
Compute the density of the rock : A geologist finds that a Moon rock whose mass is 10.15 kg has an apparent mass of 5.68 kg when submerged in water. What is the density of the rock
How much work was done during this process : An ideal gas has its pressure cut in half slowly, while being kept in a container with rigid walls. How much work was done during this process

Reviews

Write a Review

Civil Engineering Questions & Answers

  How to specify the state of stress in the wall of the tank

The tank has an inner diameter of 1.5 m and a wall thickness of 18 mm. If the pressure in the tank is p=1.20MPa, determine the force in the 16 bolts that are used to attach the cap to the tank. Also, specify the state of stress in the wall of the ..

  Calculate braking force rb at wheel rim for each system

A bicycle rider would like to compare the effectiveness of candilever hand brakes (use figure a) versus V brakes (figure part b). (a) Calculate the braking force Rb at the wheel rim for each of the bicycle brake systems.

  Find the maximum area that the rancher can enclose

A rancher has 1200 ft of fencing to enclose a double paddock with two rectangular regions of equal areas. find the maximum area that the rancher can enclose.

  Determine the moment of the couple formed by the two forces

Two parallel 40-N forces are applied to a lever. Determine the moment of the couple formed by the two forces (a) by resolving each force into horizontal and vertical components and adding the moments of the two resulting couples

  Temperature and velocity of the air-adiabatic nozzle

Air at 200 kPa and 950 K enters an adiabatic nozzle at low velocity and is discharged at a pressure of 80 kPa. If the isentropic efficiency of the nozzle is 92%, determine the temperature and velocity of the air at the exit.

  What minimum applied force is needed to open the gate

A rectangular gate is inclined at an angle of 30 degrees from the horizontal. It is 4 ft wide by 6 feet long. If it is hung from its upper end which is 8 feet below the waters top edge, what minimum applied force (bottom) is needed to open the gat..

  Find what design speed was used for a freeway exit ramp

a freeway exit ramp has a single lane and consists entirely of a horizontal curve with a central angle of 90 degrees and a length of 628 ft. if the distance cleared from the centerline for sight distance is 19.4ft, what design speed was used

  Ompare the ratio of kinetic energy to the potential energy

If a unit mass of groundwater accelerates from rest to an average linear velocity of 1 m per year and climbs a vertical distance of 1 m, compare the ratio of kinetic energy to the potential energy of the unit of groundwater.

  Determine the amount of natural alkalinity consumed

jar tests were perfomed on untreated river water. an optimum dose of 12.5 mg/L of alum was determined. determine the amount of natural alkalinity (mg/L as CaCO3) consumed.

  Determine mechanical properties of ametal by concucting test

if you were asked to determine the mechanical properties of ametal by concucting a test, what type of test whould you use, and what data can you abtain from that test

  What must the ph be raised to in order to precipitate

Groundwater in Taupe, Arizona, initially contains 1.8 mg/L of iron(III). What must the pH be raised to in order to precipitate 0.3 mg/L of the iron (T=25°C)

  Make a list of threats which may be vulnerable to company

Make a list of threats which may be vulnerable to the company's information system.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd