Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.The velocity varies linearly with time throughout the nozzle. the velocity at the base is 1t and at the tip is 4t. what is the local acceleration midway along the nozzle when t=2s? What is the convective and centripetal acceleration with L=1.5ft?
2.A gravity thickener receives 33.000 Lpd of wastewater sludge and increases the solids content from 3.0% to 7.0% with 90% solids recovery. Calculate the volume of thickened sludge.
3.The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2 in.
a round steel rod, 25 mm in diameter, subjected to a bending moment of 160 Nxm. calculate the maximum bending stress.
A 12in diameter water main in your city has become very rough due to rust and corrosion, it has been suggested that the flowrate through the this pipe can be increased by inserting a smooth plastic liner into the pipe.
If 0.100 mol each of SO2 and NO2 are placed in a 500 mL vessel at this temperature, what are the concentrations of the reactants and products when equilibrium is established for this reaction?
A trapezoidal channel with a bottom width of 4 feet and side slopes 2:1 (H:V) and a bed slope of 1 percent conveys a discharge of 50,000 gpm. Assume n = 0.025. Compute the normal depth.
Two forces are applied as shown to hook support. Knowing that the magnitude of P is 35 N, determine by trigonometry (a) the required angle a if the resultant R of the two forces applied to the support is to be horizontal, (b) the corresponding magnit..
The pressure at the entrance of the system must be at least 75 psi and the demand is 1350 GPM. The pipe material is to be riveted steel and the length of pipe is 5,000 feet. What size pipe should be used
The relative velocity of two infinitely wide parallel plates thatare 1cm apart is 10cm/s. If the dynamic viscosity of the liquid between the plates is 0.001 N s/m2 what is the shear stress between the plates?
The stream from a gas well is a mixture containing 50 mol % methane, 10 mol % ethane, 20 mol % propane, and 20 mol % n-butane. This stream is fed into a partial conderser maintained at a pressure of 250 psia
When a fluid flows through a sharp bend, low pressures may develop in localized regions of the bend. Estimate the minimum absolute pressure (pmin in psi) that can develop without causing cavitation if the fluid is water at 80 oF.
If the ball strikes the bottom of the elevator shaft in 3s, determine the height of the elevator from the bottom of the shaft at the instant the ball is released.Also find the velocity of the ball when it strikes the bottom of the shaft.
Determine the pump power in W & hp required to pump water froma tank at the base of the world's tallest building (1667 ft) to ahot tub of similar size on the roof. Ignore friction losses& changes in atmospheric pressure due to change inelevation. Flo..
A bullet is fired from a height of 150m at a velocity of 300kmph at an angle of 35 upward. Neglecting air resistance. Find: a) total time of flight b) horizontal range
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd