Calculate the steady state concentration of inorganic n into

Assignment Help Civil Engineering
Reference no: EM13550272

Colette Lake has a surface area of 103 ha and a mean depth of 8 m. The pH of the water is 7.6. The lake receives surface water from a lake upstream, rainfall, and diffuse groundwater input. Atmospheric inorganic N deposition is insignificant. Contaminated groundwater is the major source of inorganic N in the lake. During April, 62 mm of rainfall fell on Colette Lake. During the same month, 4.2 x 10^6 m^3 of groundwater having an inorganic N concentration of 8.4 mg/L flows into the lake at a rate of 21.00 m^3/s. The sedimentation rate for inorganic N was measured as 49 mg N/m^2*days. A river drains into the lake at a rate of 22.64 m^3/s. there are no other sources of water into or out of the lake. Calculate the steady state concentration of inorganic N into the lake.

Reference no: EM13550272

Questions Cloud

Determine the clearance between the tube and the cylinder : A 25-mm diameter steel cylinder 300-mm long falls, because of its own weight, at a uniform rate of 0.1 m/s inside a tube of slightly larger diameter. A castor-oil film of constant thickness is between the cylinder and the tube.
What is the fractional change in the volume of the ball : A waterproof rubber ball with bulk modulus 2.725·107 N/m2 is submerged underwater to a depth of 98.69 m. What is the fractional change in the volume of the ball
Prepare the journal entries to record transactions : The stock transactions were completed during the first year - Prepare the journal entries to record the above transactions.
Cost allocation-direct method : Service department costs to the operating departments - Cost Allocation-Direct Method
Calculate the steady state concentration of inorganic n into : Colette Lake has a surface area of 103 ha and a mean depth of 8 m. The pH of the water is 7.6. The lake receives surface water from a lake upstream, rainfall, and diffuse groundwater input
Compute the seepage velocity and estimate the hydraulic : A tracer dye is injected into a 55-ft thick sandy gravel confined aquifer which has a hydraulic conductivity of 1.2 x 10^-3 ft/s. The dye appears 14 days later in an observation well 75 ft away from the injection point.
Estimate the height and orientation of the image : A real object is 42.1 cm from a negative lens that has a focal length of 25.6 cm. The object is 2.45 mm high. The height and orientation of the image are
Determine the average impulsive force developed : The 180-lb iron worker is secured by a fall-arrest system consisting of a harness and lanyard AB, which is fixed to the beam. If the lanyard has a slack of 4 ft, determine the average impulsive force developed in the lanyard if he happens to fall 4 f..
Determine the total bond interest expense : Determine the total bond interest expense to be recognized over the bonds life and prepare a straight-line amortization table like the one in Exhibit 14.7 for the bonds' first two years.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What power is required to overcome the skin friction drag

Fluid mechanics ch.9: A supertanker has length, breath, and draught (fully loaded) dimensions of 325m, 48m, and19m, respectively. In open seas the tanker normally operates at a speed of 115 kt (1 kt=0.515m/s).

  Calculate the vertical stress at a depth of 4m vertically

Three point loads 10,000, 7500 and 9000 kN act in line 5m apart near the surface of a soil mass. Calculate the vertical stress at a depth of 4m vertically below the centre (7500kN) load.

  Determine the power required to run the compressor

Helium (Hrom an intie) at a rate of 1.5 lbm/s is compressed inan adibatic compressor from an intial condition of 70 F, 14.7 Psiato final condtion of 1070 F, 147 Psia. Determine The power required to run his compressor

  Determine the moment of inertia about ahorizontal axis

By integration, determine the moment ofinertia about a horizontal axis at the channel bottom. Using the parallel axis theorem, determine the moment of inertia about ahorizontal axis through the centroid.

  Determine the reaction at a and b by a pin

Three loads are applied to a beam. the beam is supported by a roller at A and by a pin at B. neglecting the weight of the beam, determine the reaction at A and B when P=15kips.

  Estimate the weight of concrete in four-lane highway segment

Estimate the weight of concrete in a four-lane highway segment that begins as a 3% grade climb from 1000 feet altitude to 4000 feet and then a 6% downgrade to 2500 feet

  Determine the minimum diameter a steel wire can have

If the elastic limit of steel is 5.0 10^8 Pa, determine the minimum diameter a steel wire can have if it is to support a 69-kg circus performer without its elastic limit being exceeded.

  Determine the amount of air that must be bled off to restore

When the air temperature is 25°C, the pressure gage reads 210 kPa. If the volume of the tire is 0.025 m3, determine the pressure rise in the tire when the air temperature in the tire rises to 50°C.

  Determine the maximum allowable temperature rise

Determine the maximum allowable temperature rise if the allowablecompressive stress in the copper is σ(allowable) = 19,500 psi.

  A subway train is traveling at a speed of 45 mile

A subway train is traveling at a speed of 45 miles/hour whenthe brakes are fully applied on the wheels of cars A and B, causing them to slide on the track

  Determine the velocity of roller when theta is given

The bar is confined to move along the vertical and inclined planes. The velocity of the roller at A is Va=5.2 ft/s when theta=40 . a)Determine the bar's angular velocity when theta=40. b)Determine the velocity of roller when theta=40.

  What length l of splice plate is needed

two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa. what length L of splice plate is needed if the axial load carried by the joint is 55 kN and the width (W) is 315 m..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd