User Account

All Pages

Calculate the pressure on the inside surface

Assignment Help Mechanical Engineering
Reference no: EM131149113

A thick cylinder has an inside diameter of 60 mm and an outside diameter of 100 mm. It is pressurised internally until the outer layer (surface) has a hoop stress of 300 MPa. Calculate the pressure on the inside surface.

Reference no: EM131149113

Questions Cloud

Implement the selection sort method : Write a C program that implements the Selection sort method to sort a given array of integers in ascending order.
Focus on the grammar area of given sentences : Read the following sentences, and focus on the grammar area specified in the left column. Then, complete Appendix H by selecting the correct sentence (a or b) for each number.
Determine speed discharge and power of model : A model of a kaplan turbine, one tenth of the actual size is tested under a head of 5m when actual head for proto turbine is 8.5m, When running at 120rpm at an overall efficiency of 85%, determine speed, discharge and power of model
Discuss the risk factors that should be considered : Discuss the risk factors that should be considered when determining treatment placement. What factors would indicate that inpatient or residential treatment is indicated for a client? Provide a 300 word response to the questions.
Calculate the pressure on the inside surface : A thick cylinder has an inside diameter of 60 mm and an outside diameter of 100 mm. It is pressurised internally until the outer layer (surface) has a hoop stress of 300 MPa. Calculate the pressure on the inside surface
Calculate the diameter of the strut : A steel strut is pinned at both ends. The strut has a solid circular cross section and is 6 m long. The strut collapses under a load of 100 kN. Calculate the diameter of the strut
What is the magnitude of the torque : If the maximum rotation angle at the free end of the shaft must be limited to ∅C ≤ 3?, what is the magnitude of the torque TA that can be applied to A
Program that implements the bubble sort method : Write a C program that implements the bubble sort method to sort a given list of names in ascending order.
Complete the given humanities assignment : For this piece of the Humanities Project, submit your topic choice along with your thesis and map.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Masses connected together with a mass less rigid-link

Given three masses connected together with a mass less rigid-link, where should you place the single mass if you want to replace these masses with it?

  Providing domestic hot water to a household typically

providing domestic hot water to a household typically requires 107 kj of energy per year. a typical electric water

  Determine the rate of entropy production

Steam at a pressure of 0.08 bar and a quality of 93.2% enters a shell-and-tube heat exchanger where it condenses on the outside of tubes through which cooling water flows, exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing ..

  Determine the analysis in terms of mole fractions

The analysis of a mass basis of an ideal gas mixture at 50 F, 25 lbf/in2. is 60% CO2, 25% SO2, and 15% N2. The analysis in terms of mole fractions. Determine: The apparent molecular weight of the mixture. The partial pressure of each component in lbf..

  Compute the corrosion penetration rate

Using the results of Problem 17.13, compute the  corrosion  penetration  rate,  in  mpy,  for the corrosion of iron in HCl (to form Fe2 + ions)   if   the   corrosion   current   density   is 8 X 10-5  A/cm2.

  Model to estimate parameter of robot based on the design

A Robot with two links, each link containing several sensors (three accelerometers and one IMU) based on Adriano micro controller for data fuse. The data was collected and filtered using Kalman filter. Robot parameter calculation using multiple ac..

  In a steam generator compressed liquid water at 1500 psi

in a steam generator compressed liquid water at 1500 psi 100of enters a 1-in diameter tube at the rate of 5 ft3min.

  Computer study-influence of supports on itframe behavior

Computer study-Influence of supports on Itframe behavior. (a) Using the RISA-2D computer program, compute the initial elastic deflection at midspan of the girder in Figure, given that the support at D is aroHer.

  Estimate the yielding stress of your blutack

Estimate the yielding stress of your blutack using a circular cross-section sample and weights/scales. Report three measurements.

  A normal shock stands where area is 20 cm 2 what is the

air at a stagnation pressure of 450 kpa and a stagnation temperature of 400 k flows through a converging-diverging

  Design of dc motor starter

In order for a dc motor to function properly, it must be protected from physical damage during the starting period. At starting conditions, the motor is not turning, and so EA = 0V. Since the internal resistance of a normal DC motor is very low, a..

  Using variable specific heat method

1. A Brayton cycle uses air and produces a net work of 14000 Btu/s with an inlet state of 60°F, 14.7 psi and a compression ratio of 16. The heat added in the combustion process is 400 Btu/lbm. If the thermal efficiency is 0.547 Determine: Using va..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd