User Account

All Pages

Calculate the diameter of the strut

Assignment Help Mechanical Engineering
Reference no: EM131149112

A steel strut is pinned at both ends. The strut has a solid circular cross section and is 6 m long. The strut collapses under a load of 100 kN. Calculate the diameter of the strut. assume E = 200 GPa.

Reference no: EM131149112

Questions Cloud

Focus on the grammar area of given sentences : Read the following sentences, and focus on the grammar area specified in the left column. Then, complete Appendix H by selecting the correct sentence (a or b) for each number.
Determine speed discharge and power of model : A model of a kaplan turbine, one tenth of the actual size is tested under a head of 5m when actual head for proto turbine is 8.5m, When running at 120rpm at an overall efficiency of 85%, determine speed, discharge and power of model
Discuss the risk factors that should be considered : Discuss the risk factors that should be considered when determining treatment placement. What factors would indicate that inpatient or residential treatment is indicated for a client? Provide a 300 word response to the questions.
Calculate the pressure on the inside surface : A thick cylinder has an inside diameter of 60 mm and an outside diameter of 100 mm. It is pressurised internally until the outer layer (surface) has a hoop stress of 300 MPa. Calculate the pressure on the inside surface
Calculate the diameter of the strut : A steel strut is pinned at both ends. The strut has a solid circular cross section and is 6 m long. The strut collapses under a load of 100 kN. Calculate the diameter of the strut
What is the magnitude of the torque : If the maximum rotation angle at the free end of the shaft must be limited to ∅C ≤ 3?, what is the magnitude of the torque TA that can be applied to A
Program that implements the bubble sort method : Write a C program that implements the bubble sort method to sort a given list of names in ascending order.
Complete the given humanities assignment : For this piece of the Humanities Project, submit your topic choice along with your thesis and map.
Write a c program that implements stack : Write a C program that implements stack (its operations) using a singly linked list to display a given list of integers in reverse order.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What should be the testing speed for the model in the wind

a one sixth scale model of an automaobile is to be tested in a wind tunnel at a speed corresponding to the prototype

  Calculate the entropy generated in the process in kjk use

a well-insulated chamber is divided in two parts my a thin membrane. the left side with a volume of 2000 cm3 is filled

  Calculate the temperature k of butane can butane be either

consider 2 kg of butane at pressure of 7.6 mpa in a rigid tank of 0.008 m3 volume.a calculate the temperature k of

  The ideal rakine cyle has steam leaves the boiler at

the ideal rakine cyle has steam leaves the boiler at 800psia and 1000f. the turbine exit is at 1.276 psia with a

  Titanium is stiffer than aluminum

Titanium is stiffer than aluminum, has a lower thermal expansion coefficient than aluminum, and has a higher melting temperature than aluminum. On the same graph, carefully and schematically draw potential well curves for both metals. Be explicit in ..

  What is the local heat transfer coefficient

A flat plate maintained at a temperature of 50 C experiences a flow of atmospheric air at 15 C. If the temperature gradient at the plate's surface at a given downstream location is -43 C/mm, what is the local heat transfer coefficient?

  A pot of 1kg of liquid water is heated on a mountain top

a pot of 1kg of liquid water is heated on a mountain top where the atmospheric pressure is 0.8 bar. if the liquid water

  A thick cylindrical sleeve when shrunk onto a hollow shaft

a thick cylindrical sleeve when shrunk onto a hollow shaft of a different material had its internal diameter extended

  Compressed isobaric ally until its volume is two-thirds

Ten pounds-mass of R-22 is at an initial volume of 4.059 ft3 and pressure of 200 psia. It is compressed isobaric ally until its volume is two-thirds of its initial volume. The piston is then held in place as the refrigerant cools until its temperatur..

  Write the impulse-momentum equation on the truck

A truck (T) is tied to a car (C), back bumper to back bumper. To you, the viewer, the truck is on the left, and the car is on the right (side view). Both vehicles are at rest. The rope connecting the two is initially slacked. The truck takes off, and..

  Determine the rotational speed and diameter of the runner

Determine the rotational speed and diameter of the runner - the flow angles at outlet from the guide vanes and at runner exit;

  Determine a fourier series representation of the periodic

Determine a Fourier series representation of the periodic voltage e(t) shown in Figure 7.14.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd