Calculate the percentage change in volume based on volume

Assignment Help Civil Engineering
Reference no: EM13304618

The natural water content of a saturated soil is 41% and its shrinkage limit = 20%. Gs (sp. gravity of solids) = 2.75. Calculate the percentage change in volume based on its volume at its natural water content if the soil is dried to a water content of 15%.

Reference no: EM13304618

Questions Cloud

Find the angular velocity when the person reaches the edge : A person of mass 75 kg stands at the center of a rotating merry-go-round platform of radius 3.1 m and moment of inertia 1300 kg ·m2. Calculate the angular velocity when the person reaches the edge
Has your organization traditionally placed more importance : When considering the implementation of a new change, has your organization traditionally placed more importance on internal or external drivers? Do you agree with this or not?
How far is the ray displaced as a result of traveling : A ray of light passes from air through dense flint glass and then back into air. How far is the ray displaced as a result of traveling through the glass
Find his moment of inertia at his maximum rotation rate : A 10 m platform diver during his diving can increase his rotation rate from an initial rate of 1.1 rev/s to a maximum of 2.8 rev/s. what is his moment of inertia at his maximum rotation rate
Calculate the percentage change in volume based on volume : The natural water content of a saturated soil is 41% and its shrinkage limit = 20%. Gs (sp. gravity of solids) = 2.75. Calculate the percentage change in volume based on its volume at its natural water content if the soil is dried to a water conte..
Diagram the cash flows for the project using a time line : Diagram the cash flows for the project using a time line. For each of Years 1 through 5, include the following data on your diagram (in this order) : EBIT, tax, depreciation, Operating Cash Flow (OCF), and discounted OCF.
Find the vertical forces exerted by the hinge on the beam : A shop sign weighing 230 N is supported by a uniform 115 N beam as shown in Fig. 9-54. find the vertical forces exerted by the hinge on the beam
Calculate how long will it take to completely charge tank : Describe the equation for charging a water tank. Use: H= 2m, A_s = 1m^2, density water = 1000kg/m^3, K = 2000kg hr^-1 Mass flow in = K t. Calculate how long will it take to charge completely the tank
What was the average nominal risk premium on the stock : The average inflation rate over this period was 3.25 percent and the average T-bill rate over the period was 4.3 percent.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Designing the tangent vertical curve

Due to a street crossing a roadway, the elevation of the roadway at station 3 +413.760 must be at 129.388 m. Design the curve?

  Calculate the force

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa. The washer dimensions are as follows: hole diameter is 27 mm. outside diam..

  What would equivalent equal monthly payment be in constant

Assume that you borrow $10,000 for five years (annual payments) at a market rate of 5%. Assuming that inflation is 3.5%, what would the equivalent equal monthly payment be in constant dollars

  What is the definition of a customer

What is the definition of a customer? What are some examples of internal and external customers? Is the measurement of customer satisfaction different for internal customers than for external customers?

  Determine what is total round trip travel time of tractor

a wheel tractor scraper weighing 100 tons is being operated on a haul road which is now packed. this tractor is traveling fully loaded up a 6% slope to the dump site which is 0.5 miles away. the return trip is level and is also 0.5 miles away.

  Determine the force required with an angle of 20 degrees

A 10 kg block is being pulled down a slope with an angle of 20 degrees and has a velocity of .2 m/s. Determine the force required

  Calculate the largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture. For the alloy, the plane strain fracture toughness is 24 and yi..

  Calculate the compacted cubic yards per hour with a drum

Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.

  Determine the reaction forces at points b and c

The fixture AC is designed with a screw adjustment to regulate the height of the 900 N load supported by the roller at A. The screw bears against a smooth surface at B. Determine the reaction forces at points B and C. Neglect the weight of the fix..

  Determine the head loss caused by the piers

A bridge has cylindrical piers 1 m in diameter and spaced 15 m apart. Downstream of the bridge where the flow disturbance from the piers is no longer present, the flow depth is 2.9 m and the mean velocity is 2.5 m/s.

  What will be the total vehicle delay

Assuming D/D/1 queuing, what will be the total vehicle delay?

  Determining the pumping rate

Determine the required pumping rate. the aquifer has T= 1600 m 2 /day and the wells each have radius of influence of 600m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd