Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A hollow circular post ABC supports a load P1 = 1700 lb acting at the top. A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB= 1.25 in, tAB= 0.5 in, dBC= 2.25 in and tBC= .375 in respectively.
A) Calculate the normal stress AB in the upper part of the post.
B) If it is desired that the lower part of the post have the same compressive stress as the upper part, what should be the magnitude of the load P2?
C) If P1 remains at 1700 lb and P2 is now set at 2260 lb, what new thickness of BC will result in the same compressive stress in both parts?
A garage (24 ft x 24 ft x 10 ft) is illuminated by (6) 60 watt incandescent bulbs. It is estimated that 90% of the energy to an incandescent bulb is dissipated as heat. If the bulbs are left on for 3 hours, how much would the temperature in the ga..
The Pomdeterra wastewater treatment plant produces thickened sludge that has a suspended solids concentration of 3.8 percent. They are investigating a filter press that will yield a solids concentration of 24 percent. If they now produce 33 m^3/d of ..
a job requires excavating and hauling 500 cyds (in situ) of sandy soil. in your posession is an excavator and a dump truck (capacity 30 cyds loose) the dump truck has a round trip travel time of 5 mins and 45 secs to the dump site and back.
Soil material is being assessed as a possible liner for a sanitary landfill. A soil core was collected and brought to the laboratory. A 10-cm tall section of soil has 2 cm of water continuously ponded on it. The area of the core surface is 78 cm^2..
Find the minimum length of runway required for the landing (I found to be 300ft). Find the position on the runway where the speed is 50ft/s and the time it takes for the speed to reach 50ft/s
Brine flood in a 1.9-in-long and 1.5-in-diameter core plug from the North Sea resulted in a stabilized pressure drop of 46.05 psi. The flood was carried out at 0.05 mL/min with brine viscosity of 0.443 cP. Determine the absolute permeability of this ..
However, design codes which deal with shear friction design place an upper limit on the magnitude of the shear force for which the plane can be designed. Explain why this is so.
A parachutist having a mass of 60kg is falling at 8m/s when the parachute is opened. Due to atmosphere drag, the deceleration equation is 60a=588.6-30v^2 in m/s^2.
If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each..
A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in the figure. The weight of the gate is negligible, and the hinge at O is frictionless.
The porosity of both media is 0.40, the shape factor for the anthracite is 7.5, and the shape factor for the sand is 6.0. Assume a water temperature of 60 F.
The Earth's surface creates a boundary layer in the atmosphere. The velocity profile near the surface can be expressed as a power law, u = a * y n, where the constants a and n depend on the roughness of the surface.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd