Calculate the natural frequency and damping ratio

Assignment Help Civil Engineering
Reference no: EM131344592

A 15-cm-long tube has an inside diameter of 1.0 mm and is connected to a transducer which has a volume of 1.2 mL. If the system is to operate with air at 2 atm and 20?C, calculate the natural frequency and damping ratio of the tube-transducer system.

Reference no: EM131344592

Questions Cloud

What you see as meaning of utilitarian ethical calculation : Do you take this to require some conception of what "the good" means, such that it can be identified, measured, and/or calculated in a way that is consistent across time, place, and people?.Is there any such "good" that has these characteristics, ..
Design a first order rc circuit using standard parts : Design a first-order RC circuit using standard parts (see inside rear cover) that will produce the following voltage across the capacitor: vC(t) = 10-20e-2000t V.
Calculate the resulting strain : A specimen of aluminum having a rectangular cross section 9.6 mm × 12.1 mm is pulled in tension with 35,262 N force, producing only elastic deformation. The elastic modulus for aluminum is 69 GPa. Calculate the resulting strain?
Saving lives and protecting property : What extinguishing agent can best fulfill the mission of saving lives and protecting property better than water? Why?
Calculate the natural frequency and damping ratio : A 15-cm-long tube has an inside diameter of 1.0 mm and is connected to a transducer which has a volume of 1.2 mL. If the system is to operate with air at 2 atm and 20?C, calculate the natural frequency and damping ratio of the tube-transducer syst..
What should be done to better assure that you are making : MGMT 499- Describe at least 3 criteria that would determine whether the manager is making good decisions. What should be done to better assure that you are making a good decision?
Discuss the impact that the problem : Using a reputable website or your local paper, find and describe something you would consider to be a social problem. After you have identified a social problem, discuss the impact that the problem has on individuals as well as society.
Design the first order rc interface circuit : The switch in Figure P7-45 has been in position B for a long time and is moved to position A at t = 0. Design the first-order RC interface circuit such that vO(t) = 10-10e-2500t V.
Hybridization changes in many chemical reactions : Atom hybridization changes in many chemical reactions. In each of the following reactions, determine what change, if any, occurs to the hybridization of the underlined atom. (a) SO3 + H2O → H2SO4

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine how large must the reactor be

A CMFR is to be designed to remove contaminant A from water with a steady-state efficiency of 95 percent. The decay reaction is zeroth order, with a rate constant of 0.1M/h. The inlet concentration of A is 0.5 M.

  Three cylinders from the same mix were tested

Three cylinders from the same mix were tested for strenght.  Cylinders A and B were cast in 4x8 molds while cylinder C was cast in a 6x12 mold.  The total loads were as follows; cylinder A= 65,200 lbs.,  cylinder B= 68,550 lbs., cylinder C= 151,190 l..

  Determine the total resultant force

in inclined circular gate with water on one side shown in the figure. determine the total resultant force acting on the gate and the total location of center pressure.

  What is the major head loss in a coarse concrete pipe with

What is the major head loss in a coarse concrete pipe with a diamter of 1ft that is 100 ft long. Water flows at a rate of 20 ft^3/s (viscosity of water = 2.344x10^-5 lbfs/ft^2, density of water = 1.94 slugs/ft^3) 1inch = 25.4mm

  Discuss the feasibility and the cost of such a system

iscuss the feasibility and the cost of such a system, and determine if the proposed system installed on one side of the roof can meet a significant portion of the cooling requirements of a typical house in your area.

  Calculate the low point of the curve if the intersection at

A vertical parabolic curve is to be used as a sag curve, and it is desired to know the location and elevation of the low point. The curve is 750ft long , and the minus grade of 3.6 percent intersects the plus grade of 6.2 percent at station

  Determine the maximum horizontal distance that a projectile

Determine the maximum horizontal distance that a projectile will have at a height of 60 m above the orgin if it is fired at an angle at 70 degrees from the horizontal with a velocity of 50 m/s

  Determine the critical distributed force q

The steel post BC supports the right end of the beam that has a uniform distributed force q. The post is a wide-flange section W310 x 74 which is built-in at the base C, but free to pivot at B. Allowing for buckling in either plane, determine the ..

  Determine the maximum absolute values of the shear

Draw the shear and bending moment diagrams for the beam AB, and determine the maximum absolute values of the shear and bending moment.

  Draw the event tree and for the initiating event

An intelligence data bank center requires power 24 hours a day, 7days a week. If the main power grid fails, a backup power supply isinitiated.

  Usage rates if the community has a declining growth rate

Determine how many years from now the consumption will reach its design capacity with current usage rates if the community has a declining growth rate.

  What concentration of chlorine is required

What concentration would be required if you used chlorine dioxide instead?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd