Calculate the mean standard deviation and the coefficient

Assignment Help Civil Engineering
Reference no: EM13555020

During construction of the surface layer of asphalt pavement, two samples where taken everyday to measure the asphalt content in the mix to ensure that it is within the specification limits.the target value was set at 5.5 percent with a tolerance of -+ 0.4 percent. the following asphalt content data were collected:

a) Calculate the mean, standard deviation, and the coefficient of the variation of the data.

b)Using a spreadsheet program, create a control chart for these data showing the target value and the upper and lower specification limits. comment on any trend and possible reasons.

Reference no: EM13555020

Questions Cloud

What was the students associated perception/ reaction time : An engineering student is driving on a level roadway and sees a construction sign 500 ft ahead in the middle of the roadway. the student strikes the sign at a speed of 25 mi/h.
Compute what is the speed of the bullet before impact : A 0.004-kg bullet is fired into a 0.200-kg block of wood at rest on a horizontal surface. what is the speed of the bullet before impact
Devise an absolute temperature scale where the boiling point : Devise an absolute temperature scale where the boiling point of water at 1 atmosphere (101 kPa) pressure = 100 degrees in your scale What is the ice point of water in your scale?
Evaluate the maximum magnitude of the acceleration : A 0.60- mass attached to a vertical spring of force constant 150 oscillates with a maximum speed of 0.30. Find the maximum magnitude of the acceleration
Calculate the mean standard deviation and the coefficient : Using a spreadsheet program, create a control chart for these data showing the target value and the upper and lower specification limits. comment on any trend and possible reasons.
Find the frequency of small oscillations in the vicinity : Two infinite, straight, parallel wires, each carrying current I in the same direction, are coincident with the lines (1,0,z) and (-1,0,z). What is the approximate frequency of small oscillations in the vicinity of the origin
Find the wavelength of the longitudinal wave : A uniform bar of metal, 0.40 m long, with a diameter of 2.0 cm, has a mass of 1.1 kg. Find the wavelength of the longitudinal wave in the metal, in mm
Determine the diameter of the pipe required to convey : Water at 20 °C is transported through a 200 m long wrought iron pipe with a head loss of 9.8 m. Determine the diameter of the pipe required to convey 10L/sec.
Determine how much energy must this engine extract : A heat engine operating between energy reserviors of 192.83 oC and 517.28oC has 29.32% of the maximum possible efficiency. How much energy must this engine extract from the hot reservior

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate low-dose cancer risk from occupational inhalation

this concentration is based on an assumption that the individual is generally healthy and is exposed for 8 hours per day over a working lifetime ( that is from age 18 to 65 years). assuming a body weight of 78 kg and an inhalation rate of 0.63 m^3..

  How deep is the water level in the second culvert

A rectangular culvert 4 feet x 6 feet is running full and discharging 3,500 cfm. There is no friction loss. Find the velocity in fps. The culvert empties into a 10 ft wide culvert and the velocity reduces to 0.6 fps.

  Determine the elevation of x and y which is required

The elevation of Y is 5265.879 ft. The elevation of X is required. Instrument at X: +S = 3.182,-S = 9.365,9.370, and 9.368. Instrument at Y: +S = 10.223; -S = 4.037,4.041, and 4.038. Find the elevation of X

  Determine the speed of the motorcyclist at the instant

While traveling around the curved path, the motorcyclist increases speed by 1.25ft/s^2 . Part A - Finding the time interval for the motorcyclist to reach a given acceleration If the motorcyclist starts from rest

  What is min required heat transfer rate from heat source

A waste heat source is available at 400°C. A heat engine operates using heat from this source. It rejects heat to the surroundings at 38°C. The power from the engine runs an air conditioner to keep the air inside a building at 25°C

  What would be the concentration of pollutant leaving lagoon

A lagoon with volume 1200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply.

  Explain what processes are required to be put into place

The business it to make dinner ware for various markets this will include plastic utensils (forks, knives, spoon, etc) as well as low end flat ware suitable for institutions such as high school college cafeterias.

  Which is estimated at 1 billion had that rate continued

World population 10,000 years ago has been estimated at about 5 million. what exponential rate of growth would have resulaed in the population in 1850 , which is estimated at 1 billion had that rate continued

  Determine the flow rate of the oil

Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.

  How long must radioisotope be held to meet allowable charge

A hospital waste containing 0.7µCi/L of 32P is to be disposed of. How long must the radioisotope be held to meet the allowable discharge activity

  What force will need to be applied to block downward to hold

A wood cube with 9 inch sides is inserted into water. The specific gravity of wood is 0.60. What force will need to be applied to the block downward to hold the wood cube completely submerged in water

  Determine how long should the basin be

Assume Stoke's Law holds true for the following question. You are asked to desgin a settling basin. Flow rates are 16 million gallons/day. The basin must be 4m deep, and 4m wide. Particle size ranges from 0.2-50 mm in diameter.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd