Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a copper alloy is found to have a yield strength of 240 MPa , a tensile strength of 310 MPa and an elastic modulus of 110 GPa. A cylindrical specimen of this alloy 18 mm in diameter and 400 mm long is stressed in compression and found to shorten by 3.0 mm a) calculate the operational compressive strain this copper specimen is subjected to. b) calculate the maximum strain this copper alloy can sustain without becoming plastically deformed.
given: Vf=Vi + a t and Sf=Si + Vi t + 1/2 a t Cedar points millennium force accelerates from 10 mph to 93 mph in 4.5 seconds. assuming acceleration is constant, find acceleration in ft/sec^2 and distance traveled in meters
Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results
Double the width of the window, using widen, set the height of the window so that it is the same as the width, and set the title to the new value "Square Window".
fy=50000psi, f'c=3000 span of l=28 ft, dead load not including beam weight = 3 k/ft, live load=3 k/ft, p*=0.5pb, concrete weights=150 lb/ft cubed, use h=d+2.5 inch, assume beam weight =10kN/m and phi=0.90
A 8 inch polyethylene pipe has a flow rate of 1000 gallons/minute with a linear length of 10000ft. Starting at elevation 200ft then ends at 600ft elevation. Initial pressure is 40 psi. find the friction and the head loss.
A 75g , 30cm--long rod hangs vertically on a frictionless, horizontal axle passing through its center. A 12g ball of clay traveling horizontally at 2.5m/s hits and sticks to the very bottom tip of the rod.
sand cone test has been performed . The test results: intial weight of cone + sand =13.51lb, Final weight of sand cone + sand= 4.26lb, weight of sand to fill cone=2.12lb, weight of soil from hole+bucket=12.42lb, weight of bucket=1.21lb
Two towers A and B are located on flat ground and their bases have equal elevations above sea level. A person on tower A whose eye level is 26.0 ft above the ground can just see the top of tower B, which is 105 ft above the ground. How far apart a..
An increment of vertical stress of150kpa compress the sample to a void ratio of1.43. What is the over consolidation ratio of the soil at the unloaded condition.
Assume the earth is a sphere with a radius of 6,371,000.000 meters. Three points are defined by their latitude and longitude. Point Latitude (N) Longitude (W) A 40° 25' 48.67" 86° 54' 54.00" B 40° 25' 47.00" 86° 54' 54.00" Purdue CE C 40° 25' 47.0..
Consider a cold worked C11000 copper alloy rod 21 mm in diameter and 250 mm in length. Calculate (a) the maximum tensile load, in N, and (b) the maximum length, in mm, to which the rod may be stretched without plastic deformation.
An aluminum link is subjected to axial tension. The loading is limited by the conditions of not yielding and not elongating excessively. The yield limit is satisfied if the stress remains below 50%of the 325M Payield stress.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd