User Account

All Pages

Calculate the maximum power which may be supplied

Assignment Help Mechanical Engineering
Reference no: EM132416650

A drive shaft runs at 350 rev/min and transmit power from a pulley A at one end to two pulleys B and C which each drive a machine in a workshop. The distance between pulleys A and B is 3 m and that between B and C is 2.4 m. The shaft between A and B is 50 mm diameter and between B and C it is 40 mm diameter.

If the maximum permissible shear stress in the shaft is 80 MN/m2.

1. Calculate the maximum power which may be supplied from each of the pulleys B and C, assuming that both machines are in operation at the same time.

2. Calculate the total angle of twist of one end of the shaft relative to the other when running on full load. G = 80GN/m2.

Reference no: EM132416650

Questions Cloud

What is the nominal rate at which energy must be extracted : If 10 rods of length L=1 m are processed per hour, what is the nominal rate at which energy must be extracted from the bath (the cooling load)?
Estimate how long must they remain in the furnace to achieve : Carbon steel (AISI 1010) shafts of 0.1-m diameter are heat treated in a gas-fired furnace whose gases are at 1200 K and provide a convection coefficient
What is the heat loss per fin : If 200 such fins are spaced at 5-mm increments along the tube length, what is the heat loss per meter of tube length?
Determine the principal stress at a point on the surface : The thin-walled pipe has an inner diameter of 0.5 in and a thickness of 0.025 in Part A If it is subjected to an internal pressure of 451 psi and the axial tens
Calculate the maximum power which may be supplied : Calculate the maximum power which may be supplied from each of the pulleys B and C, assuming that both machines are in operation at the same time.
Calculate the hoop and longitudinal stresses present : Calculate the hoop and longitudinal stresses present in the cylinder and determine what torque may be applied to the cylinder if the principal stress is limited
Final temperature of the irradiated surface : (a) The final temperature of the irradiated surface after 30 min is ?ºC. (b) Will the code requirements be met?
Determine the power output for type of system : a) Determine the power output for each type of system for a basic collector area. b) Determine the exergy destroyed for each type of system.
What should be the minimum inlet valve area : The maximum inlet-valve flow coefficient is estimates at 0.40. What should be the minimum inlet valve area?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +91-977-207-8620

Phone: +91-977-207-8620

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd