Calculate the mass flow rate of methane in g per min

Assignment Help Civil Engineering
Reference no: EM13312499

A previously calibrated rotometer is being used to measure a gas flow. The old calibration curve is a straight line described by the following equation:
Q=1.10RR-0.50
Where
Q=flow, liters/minute
RR=rotometer readi g, dimensionless
The rotometer was calibrated using ethane (C2H6) at 1.40atm and 60*F. The gas presently bei g used is methane (CH4) at 1.10atm and 100*F.

A. Calculate the true volumetric flow rate of methane in the rotometer whe. The rotometer reads 4.0.

B. Calculate the mass flow rate of methane in g/min.

Reference no: EM13312499

Questions Cloud

Determine the time at which the pressure in the tank : The velocity out of the tube may be approximated by V = √(2(p-patm)/ρ), where p is the absolute tank pressure. Determine the time at which the pressure (gage) in the tank is 20 kPa if the initial pressure is 40 kPa (gage)
Explain what is the molar mass (g/mol) of the unknown gas : Hydrogen gas effuses at a rate 4.5 times that of an unknown gas under the same conditions. What is the molar mass (g/mol) of the unknown gas
Estimate the daily emissions of particles from a solid-waste : The incinerator burns 50 tonnes per day (1 tonne= 1 metric ton= 1000kg) and exhausts gases in a ratio of 20kg of gases per kg of feed. Assume the gases exit at 200*C and 1atm.
Explain what is the molarity of a solution made : What is the molarity of a solution made with 2.4g if LiOH (molar mass = 23.9g/mol) dissolved to make 1.5L of solution? I want to know how to set up the formula for this problem
Calculate the mass flow rate of methane in g per min : A previously calibrated rotometer is being used to measure a gas flow. Calculate the true volumetric flow rate of methane in the rotometer whe. The rotometer reads 4.0.
Compute the voltage for a concentration cell : Using the Nernst Equation, calculate the voltage for a concentration cell with: Cu (s)| 0.01 M Cu2+|| 1.0 M Cu2+| Cu (s)
What is the inductance : An RLC circuit consists of a 48 ohm resistor, 240 micro farad capacitor, and an inductor. What is the inductance
What is the average power of the elevator motor : A 668-kg elevator starts from rest and moves upward for 4.30 s with constant acceleration until it reaches its cruising speed, 1.65m/s. What is the average power of the elevator motor
Compute voltage for a concentration cell : Using the Nernst Equation, calculate the voltage for a concentration cell with: Cu (s)| 0.01 M Cu2+|| 1.0 M Cu2+| Cu (s)

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine elevation vs surface area relationship for vault

An underground storage vault is to be constructed to serve as a detention pond for a heavily urbanized area. The walls of the vault will be vertical, but the flow will be sloped along its length to promote drainage.

  Find the air pressure at the height on air pressure

The efficiency of the engines of subsonic airplanes depends on air pressure and usually is maximum near about 36,000 ft. Find the air pressure y(x) at this height. The rate of change y(x) is proportional to the pressure

  Determine the shear-thrust and moment in the arch at point c

The three hinged arch is composed of segments of a circle. Support points A and D are not at the same level.Determine: (a) the horizontal and vertical components of reaction at A and D.

  Determine how many years from consumption will reach

A community has a current population of 15,000. 10 years ago, the population was 12,500 and the community has a declining growth rate with a saturation population of 22,000.

  Determine what is the magnitude of the load p

A round bar of 6mm diameter is made of 6061-T6 aluminum. When the bar is stretched by an axial force P, its diameter decreases by 0.450 microns. what is the magnitude of the load P

  Determine what must the pipe diameter be

If a flow of 5.0 cfs is to be carried by an 11000 ft cast-iron pipeline without exceeding a head loss of 137 ft, what must the pipe diameter be

  What is the probability that the maximum 24 hour depth

Using the Gumbel probability function, estimate the probability that a maximum 24 hour depth in any year will exceed 160 mm. What is the probability that the maximum 24 hour depth will exceed 125 mm

  Determine the dead load in pounds per linear foot for beams

The beams support one-way slabs, 6 inches thick that span 20 feet center to center. Assume that the beams are 16 inches wide and 24 inches deep. Determine the dead load in pounds per linear foot for the beams, from the concrete structure alone.

  Find the force that these gas generates on the top

the circular top of a can has a radius of .0320m. the pull-tab has an area of 3.8x10^-4 m^2. the absolute pressure of the carbon dioxide in the can is 1.40x10^5Pa. find the force that these gas generates on the top of a can?

  Determine what will be the max torque of a solid steel shaft

A solid steel shaft of circular cross section and diameter 6 inches in pure torsion under torque. If E=30x10^6 pse and max shear stress is 30 ksi, calculate the torque. If the shaft was hollow, with an innner diameter of 2 inches and outer diameter..

  Find waters carbonate hardness and noncarbonated hardness

A municipality uses green energy and treats 15 × 106 gal/day of a groundwater containing the following: CO2 = 17.6 mg/L, Ca2+ = 80 mg/L, Mg2+ = 48.8 mg/L, Na+ = 23 mg/L, Alk(HCO3-) = 270 mg/L as CaCO3, SO42- = 125 mg/L, Cl- = 35 mg/L.

  Determine what the height should be to force to be critical

Given that uniform flow is subcrital and there is a weir in a rectangular channel, how do you determine what the weir height should be to force the flow to be critical. Draw this transition on a specific energy curve.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd