Calculate the magnitude of the electric field in side

Assignment Help Civil Engineering
Reference no: EM13528868

A point charge of -2.00μC is locatedin the center of a spherical cavity of radius 6.51cm inside aninsulating spherical charged solid. The charge density in the solid7.34*10^-4 C/m^3. Calculate the magnitude of the electric field inside the solid at a distance of 9.5cm from the center of the cavity.

Reference no: EM13528868

Questions Cloud

Sketch a typical floor plan and indicate the tributary : A 10 storey building measures 20m x 40m in plan and has columnslocated on a grid 10m x 10m. The floor consists of a 250mm thick R/C slab with droppanels 3m x 3m x 200mm thick in the vicinity of each column. Live load allowanceis 3.0kPa.
What is the detention time in the cstr : Assume the overall system is at steady-state, theflow rate is 15 L/min, the detention time is the PFR is 1.5 hours,and the decay rate of compound A is defined by a first-order ratereaction (k = 1 h-1).
The question asks for the magnitude and direction : The question asks for the magnitude and direction at the pin Aand int the cable BC needed to support a 500-lb ball load. The boomweight AB is neglected. AB is 8ft long and angled at 35degrees. The cable BC has an angle of 22 degrees and the500-lb bal..
What is the volume of this piece of ore : An irregular piece of unknown ore weighs 7 lb in air and was found to weigh 5.6 lb in water when submerged.
Calculate the magnitude of the electric field in side : A point charge of -2.00μC is locatedin the center of a spherical cavity of radius 6.51cm inside aninsulating spherical charged solid. The charge density in the solid7.34*10^-4 C/m^3.
Find the exact current through the third resistor : A battery supplies 0.77 A to three resistors connected in parallel. What is the exact current (in A) through the third resistor
Find the normal force exerted by the plane on the block : A block weighing 10.82 N rests on a 34° inclined plane. Find the normal force exerted by the plane on the block
Find the centripetal acceleration of the tip of second hand : The speed of the tip of the minute hand on a town clock is 0.00125 m/s. find the centripetal acceleration of the tip of the second hand
Find the change in diameter under load answer in mm : A cylinder of rock with a Poisson's ratio of 0.422 has ano-load length equal to 17.6 cm and a no-load diameter of 6.20cm. Under an axial compressive load the axial strain is foundto be -3.44 mm/m.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the mass and volumetric composition of 1 hcp

For a cement paste with an initial water-cement ratio of 0.5, by mass, calculate the mass and volumetric composition of 1 cm^3 of HCP under both wet and sealed curing conditions.

  Determine minimum surge tank size for max allowable height

A hydroelectricity plant is supplied from a resevoir via a pipeline 2km long and 2.5m in diameter. The pipeline terminates at the downstream end at in a control valve. Determine the minimum surge tank size if the max allowable height

  Determine what is the volume of the lake in cubic feet

Nitrification, the conversion of ammonia to nitrate (NH3 -> NO3-) occurs in the lake according to first - order kinetics. One stream feeds the lake and one stream empties the lake with the flow rate in both being 8 cfs

  Find expected value of number of days the car encounters

A particularly long traffic light at an intersection is green 20% of the time. A car approaches this intersection once each day. Let X represent the number of days the car encounters a green light.

  Determine the maximum power output of the pelton wheel

A Pelton wheel, located at an elevation of 200.0 m, is used to extract power from a reservoir at an elevation of 800 m. A penstock 1500 m long and 0.8 m in diameter connects the reservoir with the nozzle of the Pelton wheel.

  Determine the allowable load p for the safety factor

a plane truss is subjected to a loads 2P and P at joints B and C, respectively, as shown in figure part a.The truss bars are made of two L102 x 76 x 6.4 stell angles having an ultimate stress tension equal to 390 MPa (cross-sectional are of the tw..

  How to estimate the time of submersion in years

Apiece of corroded steel plate was found in a submerged ocean vessel. it was estimated that the original area of the plate was 62.5cm 2 and approximately 2.8k had corroded away during the submersion.

  Determine the force in members gf-fb and bc

determine the force in members GF,FB, and BC of the Fink truss and state if the members are in tension or compression

  Determine suitable footing dimensions to suit the bearing

Determine suitable footing dimensions to suit the bearing capacity of 100kPa with a factor of safety 2.4

  Seepage velocity and estimating hydraulic gradient

The dye appears 14 days later in an observation well 75 ft away from the injection point. Compute the seepage velocity and estimate the hydraulic gradient in the aquifer if the porosity of the soil is 42%.

  Find what is the depreciation charges expect on the laptop

A laptop has a four year life span with an initial cost of $900 and $100 salvage value. According to the straight line method what is the depreciation charges you expect on the laptop

  Calculate required downpayment and monthly payments for loan

Terry wants to purchase a used car for $8000. The dealer offered to finance the deal at 8.5% APR for 4 years with 10% down payment. Terry's bank will provide a loan at 7.8% for 3 years, but wants a 20% downpayment.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd