Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Problem 1: A truss is shown in the figure below. Calculate the horizontal deflection of joint D produced by both the load and fabrication error (bar AE is 30mm too long). For all the bars, area A = 1000 mm2, E = 200 GPa.
Problem 2: Solve the support reactions at A and D using the force method. A is a fixed support; B and C are rigid joint and D is the pin support. EI is constant for all the members.
-------------------------------------------
Provide the step by step solution in PDF format. Include all the steps....
A stepped shaft ACB having a solid circular cross sections with two different diameters is held against rotation at the ends. If the allowable shear stress in the shaft is 60MPa, what is the maximum torque (To)max that may be applied at section C?
A reinforced concrete beam having the cross section shown is on a simple span of 28ft. It carries uniform service loads of 3.60 kips/ft live load and 2.20 kips/ft dead load. Check the adequacy of the beam with respect to the moment.
A water pipe, in diameter id located in a trench 450mm below the center of the slab. The trench running along the length of the slab,300mm wide and 450mm deep, was backfilled with the same soil. If this pipe were to leak, what effect would it have..
A car is traveling up a 3% grade on a road that has good, wet pavement. The engine is running at 2500 rpm. The radius of the wheels is 15 inches, the driveline slipage is 3% and the overall gear reduction ratio is 2.5 to 1
The kinetics of the austenite-to-pearlite transformation obey the Avrami relationship. Using the fraction transformed-time data given below, determine the total time required for 95% of the austenite to transform to pearlite
Colette Lake has a surface area of 103 ha and a mean depth of 8 m. The pH of the water is 7.6. The lake receives surface water from a lake upstream, rainfall, and diffuse groundwater input
Refrigerant 134a enters the condenser of a residential heat pump at 800 kPa and 35 degrees celcius at a rate of 0.018 kg/s and leaves at 800 kPa as a saturated liquid.
The diameter of the hole is normally distributed with a mean 15 cm and standard deviation 0.025 cm, and the diameter of the piston is normally distributed with mean 14.88 cm and standard deviation 0.015 cm.
A crop has a consumptive use requirement of 1.2 acre-ft of water per acre of crop land. The crop is planted on 780 acres. Precipitation is 3.2 inches. The remainder of the 1.2 ac-ft/ac requirement is met by irrigation.
The performance functions of these three routes are: t1=50+0.2v1, t2=80+0.1v2, t3=120 + 0.05v3 t1, t2, t3 and are travel times in minutes; v1, v2, v3 are flows in number of trucks per day.
While traveling around the curved path, the motorcyclist increases speed by 1.25ft/s^2 . Part A - Finding the time interval for the motorcyclist to reach a given acceleration If the motorcyclist starts from rest
A fixed beam of span 6m carries point loads 20kN and 15kN at 2 m and 4 m from the left end respectively. Find the support movements draw SFD and BMD
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd