Calculate the essential bandwidth using energy percentage

Assignment Help Electrical Engineering
Reference no: EM13227807

a. Plot the spectra of X(w) = t sinc(wt/2). Let t = 1 and -20 =< w =< 20

b. Calculate the energy within this bandwidth using the "quad" function.

c. Calculate the essential bandwidth using (i) 90% and (ii) 96% energy.

Reference no: EM13227807

Questions Cloud

How did you stimulate recall of prior knowledge : How did you stimulate recall of prior knowledge? What else might you have considered using and what two instructional delivery methods did you utilize? What else might you have considered using?
Compute the ph and concentration of all species : calculate the pH and concentration of all species present assuming that the activity coefficients are equal to 1.0 for all species
how many clerks and typists should be hired : how many clerks and typists should be hired assuming a 80 percent target utilization rate?
Explain deduced from the presence of the decay products : A rock is found to contain 83.7% of the amount of uranium-238 that it contained when it was formed. (The amount that the rock contained when it was formed can be deduced from the presence of the decay products of u-238 .) How old is the rock?
Calculate the essential bandwidth using energy percentage : a. Plot the spectra of X(w) = t sinc(wt/2). Let t = 1 and -20 =
What is the maximum revenue with a single shift : Using Equation 2.1 d. What is the maximum revenue with a single shift? e. What is the break-even volume with a two-shift operation?
What is the maximum effective capacity of the system : What is the maximum effective capacity of the system in number of passengers per hour?
Does the firm need to buy more machines : Forecast demand: 60 79 81 84 84 Demand/capacity ratio c. Does the firm need to buy more machines? If so, how many? When? If not, justify.
Explain absorb energy or emit energy : As the electron in a hydrogen atom jumps from the = 3 orbit to the = 7 orbit, does it absorb energy or emit energy?

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  The design must show all stages used in its development

The design must show all stages used in its development and must be implemented and tested in PSpice and suitable timing waveforms produced.

  Determine the standing wave pattern for the voltage

Determine the standing wave pattern for the voltage in the line. Express the result in real insantaneous form and simplify

  Write the equation for the acceleration

Write the equation for the acceleration as a function of the position change of the platform.

  Is there any advantage or disadvantage of star connection

Is there any advantage of star connection over delta w.r.t. induction motors? Also, is there any advantage or disadvantage of star connection over delta w.r.t. distribution and transmission of power? Please explain the reasons for all the advantag..

  How the signals were changed to a power level

A typical method of measuring the linearity of an amplifier is called the "Two-tone" test. Signals at f1 and f2 are input to the amplifier and the output spectrum is observed. Assuming that signals at 14.1 and 14.2 MHz are input to an amplifier.

  Determine value of c to ensure a unit energy constellation

S = {c(k + jl) | k = 3, 1, 1, 3 and l = 3, 1, 1, 3 and j = square root of -1, where c is a constant. Determine the value of c to ensure a unit energy constellation. Sketch this constellation. Find d^2 min and label the constellation points with bi..

  Find the value of the lumped elements c and l

A.) We would like to use a series lumped element b to match this load. What is the length of the line where the normalized input impedance is z= 1-jb(d/\lambda). If the rfequency is 1GHz , find the value of the lumped element(C or L).

  Explain what is the framework or reference model

1. There are 4 main classes of network topologies, what are they 2. In communications over a network, protocols are required. What is the framework or reference model that makes this possible

  Define nmos fet and bjt analysis

A standard silicon NPN BJT is to be used as an amplifier. The emitter voltage is biased at 4 volts, the base is biased at 5 volts, and the collector is biased at 10 volts. Will this circuit perform as desired? Why or why not.

  What is a relative addressing mode

Discuss different types of addressing modes of HCS12. What is a relative addressing mode What is the difference between a direct and an extended addressing mode Discuss how Registers X and Y are used in index addressing mode.

  Define the voltage and current in the laplace domain

The voltage and current in the Laplace domain for a certain system is given by V (s) = 1/12 1/s^2 +3, I(s) = s/s^2+3. Is this system best described as resistive, capacitive, or inductive?

  Use mips assembly language

Write an assembly program to calculate sum of number10 through 25

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd