Calculate the difference in elevation from a to b

Assignment Help Civil Engineering
Reference no: EM131147008

In trigonometric leveling from point A to point B, the slope distance and zenith angle measured at A were 2504.897 m and 85°08'54". At B these measurements were 2504.891 m and 94°52'10" respectively. If the instrument and rod target heights were equal, calculate the difference in elevation from A to B.

Reference no: EM131147008

Questions Cloud

Explain forces that shape competitive element in an industry : Explain The five forces that shape competitive elements in an industry. Review all required readings, including the Weekly Briefing, which provides additional guidance on how to complete the Assignment.
What is the angle in seconds subtended by one division : With the bubble centered, a 150-m-length sight gives a reading of 1.208 m. After moving the bubble four divisions off center, the reading is 1.243 m. For 2-mm vial divisions
What error results for a 20-sec bubble : An observer fails to check the bubble, and it is off two divisions on a 100-m sight. What error results for a 20-sec bubble?
How do you tell story using only dialog and stage direction : How do you tell a story using only dialog and stage directions? (This is a unique challenge) What is the tone of your play? (Comedy, drama, or a mix?)  How does your play end? (This is entirely up to you)
Calculate the difference in elevation from a to b : If the instrument and rod target heights were equal, calculate the difference in elevation from A to B.
Describe the type of decision making information : You are hired as a management consultant to help this company solve some of its system problems - Describe the type of decision making information that probably would be needed by the companys.
What error results from curvature and refraction : Successive plus and minus sights taken on a downhill line of levels are listed in Problems . The values represent the horizontal distances between the instrument and either the plus or minus sights. What error results from curvature and refraction..
Weaknesses of individually administered achievement tests : Describe two (2) strengths and two (2) weaknesses of group administered achievement tests and two (2) strengths and two (2) weaknesses of individually administered achievement tests. Which do you think is more effective? Provide two (2) supporting..
Analyze traditional theories of assessment : Develop a creative, appealing presentation using your chosen tool for a professional audience, using two to three (2-3) colors, two to three (2-3) fonts, and two to three (2-3) other visuals. Provide coherent, clear, organized, and substantive con..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find correct horizontal distance considering a gentle slope

A civil engineer used a 30-m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial and the end point was found to be 1.25 m.

  Determine the time it takes for the particle to come to

A particle is traveling in a straight line at a constant speed of 22.9 m/s. Suddenly, a constant force of 10.7 N acts on it, bringing it to a stop in a distance of 63.6 m.

  Determine depth result upstream during design flood event

A 1.5m diameter barrel (concrete barrel, well-rounded entrance) that is 20 m long is installed on a slope of 2 percent. The design discharge is 9.5 m^3/s and the inlet will be submerged but not the outlet.

  Determine the final temperature and boundary work

Determine the final temperature and the boundary work done during this process.

  Determine the tension t in the cable

Determine the tension T in the cable and the magnitude of the pin reaction at O

  Need to select a hydraulic pump size and a hydraulic

An Engineer is designing a hydraulic lift with a capacity of 10 tons. The moving parts of this lift weigh 1000 lbf. The lift should raise the load to a height of 6 ft in 20 sec.

  Set up the problem and constraints using algebraic symbols

Two factories are manufacturing and supplying a single type of good to four warehouses. The factories can produce a1, and a2 units of the good each month, and the warehouses need b1, b2, b3, and b4 units each month

  Find all the support reactions at point a and b

Determine the force in each member of the scissors truss shown in Figure 2. State the whether the members are in tension or compression. The reactions at the supports are given.

  Explain qualitative difference between the sine and tangent

Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results.

  Determine by trigonometry the required tensoin t2

determine by trigonometry (a) the required tensoin T2 in the left hand portion if the R of the force exerted by the cable at A is to be vertical, (b) the corresponding magnitude of R.

  What are the reasons for organisms that have mercury

What is (are) the reason(s) for organisms that have mercury concentrations different than what is predicted to occur just by bioconcentration

  Where have movement joints been placed in these walls

Where have movement joints been placed in these walls? What type of joint is each? Why is it placed where it is? Do you agree with this placement?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd