Calculate max tensile force that the cable can withstand

Assignment Help Civil Engineering
Reference no: EM13304044

A cable is made of two strands of different materials, A and B, and cross sections as follows: For material A, K = 60, 000 psi, n = 0.6, Ao = 0.6 in2 For material B, K = 30, 000 psi, n = 0.5, Ao = 0.3 in2 Calculate the maximum tensile force that this cable can withstand prior to necking on strand A and B (Non of the strands A or B should pass their necking region).

Reference no: EM13304044

Questions Cloud

How many sales dollars has the firm generated : The Du Pont identity can be used to help managers answer which of the following questions related to a firm's operations?
What are the four different approaches : Calculate operating cash flow using the four different approaches described in the chapter and verify that the answer is the same in each case.
What enterprise value do you estimate for creed : Neither Creed nor its acquisition target, Organic and More, uses debt financing at present. However, The VC has offered to provide the acquisition financing in the form of convertible debt that pays interest at a rate of 8 percent per year and is ..
Explanatory function and predictive function : Can you please select the one theory that you believe has the highest degree of “explanatory function” and the one that has the highest degree of “predictive function”.
Calculate max tensile force that the cable can withstand : A cable is made of two strands of different materials, A and B, and cross sections as follows: For material A, K = 60, 000 psi, n = 0.6, Ao = 0.6 in2 For material B, K = 30, 000 psi, n = 0.5, Ao = 0.3 in2
Consequence of the black death-recovery of post-plague : Which of the following was not a consequence of the Black Death in China? What did the Medici family contribute that helped the economic recovery of post-plague Europe? Which conquered group did Kublai Khan attempt to make peace with in order to main..
An rlc circuit is an electrical circuit consisting : An RLC circuit is an electrical circuit consisting of a resistor, an inductor, and a capacitor, connected in series or in parallel. some important properties of this type of circuit are the resonance frequency f0 and damping attenuation.
Report an example of a euphemism or dysphemism : Report an example of a euphemism or dysphemism that you have come across. Discuss when it is and is not appropriate to use such veiled language.
Stage of global development-international operations : Which of the following describes the supply chain strategy for the “International Operations: local presence” stage of global development?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design a logic circuit

Design a logic circuit that, when enabled with an active-high signal named en, will detect four different ranges of values for a 5-bit input number.

  Determine what is the design speed of the curve

An equal tangent vertical curve connects a -2% and a +3% grade. The low point of the curve is at elevation 297.88 ft. If the PVI is at elevation 295 ft, what is the design speed of the curve

  Determine the magnitude of the smallest velocity reached

The motion of a particle is defined as x=t^2-8t+7 and y=0.5t^2+2t+4, where x and y are in meters and t is in seconds. Determine the magnitude of the smallest velocity reached by the particle, and the time, position, and direction of that velocity.

  Determine total charge for billing period based on rate

A large residence consumes 3705 kWh of electrical energy over a billing period. Determine the total charge for the billing period based on the rate schedule provided. The margin of error is $0.5

  Determine the equilibrium mole fraction of hcho in air

At equilibrium, the air space has a volume of 1 L, a total pressure of 1 atm, and a temperature of 298 K. The i mg of formaldehyde (HCHO, MW = 30 g/mol) is injected through the septum into the water.

  Design condition inflow and pumping rates

Derive an equation that allows you to compute the diameter of the drain hole for a desired steady water height in the tank for the design condition inflow and pumping rates.

  What is the average velocity

hydrogen is flowing in a 50 mm diameter pipe at a mass rate of 0.01 kg/s. at section 1 the pressure is 280 kPa abs and t= 25 . what is the average velocity?

  Prtoblem on uniform decelerated motion

Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off. (b) 9 s later.

  Plot ground level concentration of sulfur dioxide as functn

Plot the ground level concentration of sulfur dioxide as a function of distance from the stack and determine the maximum ground level concentration at both with and without air pollution control and the distance from the stack where the maximum co..

  Determine maximum amount fabco should be willing to pay

Fabco, Inc., is considering purchasing flow valves that will reduce annual operating costs by $10,000 per year for the next 12 years. Fabco's MARR is 7 percent/year. Using an internal rate of return approach

  Calculate by what factor the mass of propane has increased

A typical propane tank that we use for barbeque initially contains a pressure of 10 psi. The pressure is low, so we take it to the local store to fill the tank with more propane. After filling,the pressure is 100 psi.

  Determine the magnitude and direction of the resultant

Part of the roof of a sports stadium is to be supported by the cables AB and AC. The forces the cables exert on the pylon A to which they are attached are represented by the vectors FAB and FAC.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd