Calculate how many chlorine atoms will be in an average

Assignment Help Civil Engineering
Reference no: EM13320852

Polychloroprene is an amorphous polymer used in o-rings due to its excellent chemical resistance and has recently been used as an iPod holder. It is known by the trade name neoprene. It has the same mer structure as polybutadiene except that one of the hydrogens next to the double bond is replaced by a chlorine atom. It has a molecular weight of 200,000 g/mol, density of 1.23 g/cc, Tg = -75°C, and Tm = 120°C.

a) Calculate how many chlorine atoms will be in an average neoprene chain?

b) Sketch the bonding between polychloroprene chains due to sulfur linkages as neoprene is vulcanized into an elastomer.

c) You decide to go swimming in Bear Lake in late November using a neoprene wet suit. Calculate the difference in viscosity (in Pa-s) between the inside and the outside of the wet suit if the water temperature is 5°C and your well-insulated wet suit keeps your body at 37°C.

Reference no: EM13320852

Questions Cloud

An organizational design plan : An organizational design plan
Find the force on the charge : If the charge is 23 mu/C, the velocity is 1500 m/s, find the force (magnitude and direction) on the charge.
Risk-taking is an important aspect of the leadership : Embracing change requires risk-taking, which needs to be as calculated as possible and based on knowledge rather than mere guesses.
Find the magnitude of the gravitational force : The Earth (5.98 x 10^24 kg) and the Moon (7.35 x 10^22) kg are separated by an average distance of 3.84 x 10^8 m
Calculate how many chlorine atoms will be in an average : Polychloroprene is an amorphous polymer used in o-rings due to its excellent chemical resistance and has recently been used as an iPod holder. It is known by the trade name neoprene.
What is the minimum mass : The first mass M (9.50 kg) is sitting on an inclined plane whose angle above the horizontal is 35 degrees. What is the minimum mass, m, in kg, needed to keep the block from sliding down the incline
What should be mixture ratio of pure water to river water : A river with 400 ppm of salts (a conservative substance) and an upstream flow of 25 m^3/s receives an agricultural discharge of 5.0 m^3/s carrying 2000 mg/L of salts.
Evaluate the attractiveness of the industry : Conduct an industry analysis using Porter's 5 forces to evaluate the attractiveness of the industry with respect to the profitability of bottlers.
What is the velocity at apogee : Astronomers have observed a planet orbiting a near-by star. Through close observation, What is the velocity at apogee, in km/s, for the planet

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the station and elevation of the curve turning point

Set up a table showing curve elevations at the PVC, at the PVT, and at the half-station points along the curve. Compute the station and elevation of the curve turning point.

  Calculate the pressure in point 1 and the density of fluid

A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.

  Find the absolute-gage and vacuum pressure heads

A glass jar is heated in an oven and sealed when the air pressure is 103 kPa and the temperature is 105 C. Find the absolute, gage, and vacuum pressures in the jar when it cools to 20 C.

  Sufficient collapse strength

Would a 30 slot stainless steel screen (2.0 m long; located at the bottom of the well) have sufficient collapse strength for this application?

  Calculate the maximum mounding height from the canal

If the hydraulic head in the canal is 100 ft and in the drainage ditch it is 80 ft calculate the maximum mounding height and the mounding distance from the canal that will occur if the farmer irrigates at a rate of 2 acre-ft/acre/year.

  Predict aqueous phase equilibrium concentration of phenan

Predict the aqueous phase equilibrium concentration of phenanthrene at 25*C if the values for this compound are Cs = 1.1 mg/L, P^v = 1.6 x 10^-7 atm, KH = 4.0 x 10^-5 atm*m^3/mol, and logKow = 4.52.

  Determine the hydraulic conductivity of an artesian aquifer

An experiment was conducted to determine the hydraulic conductivity of an artesian aquifer. The piezometric heads at two points 150m apart were found to be 55 m and 48.5 m above a datum.

  Determine the dimensions of an ideal circular settling tank

determine the dimensions of an ideal circular settling tank that can remove 0.01-in diameter particles with a specific gravity of 1.01. Use a detention time of 1.5 hours, flowrate= 4ft^3/sec, the specific weight of water=62.4 lb/ft^3

  Determine the density in si unit of brass

The specific weight (wt./Vol.) of brass is 520 lb/ft^3. Determine its density (mass/vol.) in SI units. Use an appropriate prefix.

  Find what is the greatest vertical height ball achieves

a ball is thrown with a valocity of 30 m/s at an angle of 40 degrees above the horizontal from the top of a 100m tall building. what is balls velocity when it lands. (neglect air resistance in both cases) DO NOT USE 2D projectile motions, only work ..

  What is the maximum positive coordinate reached by particle

The position of a particle moving along an x axis is given by x = 17t2 - 5.0t3, where x is in meters and t is in seconds. (a) Determine the position, velocity, and acceleration of the particle at t = 3.0 s. x = m v = m/s a = m/s2

  Draw a queue diagram representing the traffic flow starting

an incident occurs on a freeway that has a capacity in the northbound direction, before the incident, of 4000 veh/h and a constant flow of 2900 veh/h during the morning commute.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd