User Account

All Pages

Calculate diameter of this steel rod when it is under load

Assignment Help Mechanical Engineering
Reference no: EM13714066

A 1 m steel rod (circular cross-section) has a diameter of 2 cm and is pulled in tension with a load of 50 kN. The steel rod experiences an entirely elastic elongation of 1 mm. a) Calculate the elastic modulus of the steel. b) Calculate the diameter of this steel rod when it is under load, assume v=0.30.

Reference no: EM13714066

Questions Cloud

The loaded symmetrical truss : Determine the forces in members BC and FG of the loaded symmetrical truss. Show that this calculation can be accomplished by using one section and two equations, each of which contains only one of the two unknowns.
Estimate the radiation reaching the earth : Please use the radiation fundamental and sun’s size to recalculate the sun radiation power and mass loss rate. Please also estimate the radiation reaching the earth!
What is the minimum amount of coal : A power plant generates steam from coal burning which burns at 3,000oF and produces about 13,000 BTU per pound. The steam is put into a poorly insulated turbine which allows 2,000 BTU per pound of coal to escape to the atmosphere at 90oF.
What would be the flexural strength of the ceramic : A three-point bending test is conducted on an aluminium oxide ceramic with a circular cross section. The ceramic has a radius of 4 mm. The specimen fractures at a load of 1100 N as measured by an Instron universal tester. If the distance between the ..
Calculate diameter of this steel rod when it is under load : A 1 m steel rod (circular cross-section) has a diameter of 2 cm and is pulled in tension with a load of 50 kN. The steel rod experiences an entirely elastic elongation of 1 mm. a) Calculate the elastic modulus of the steel. b) Calculate the diameter ..
Consider a recalculating flow in the power cycle : Consider a recalculating flow in the power cycle shown in the figure. The fluid flowing in 100 ft of smooth pipe have an average specific weight of 50 lbf/ft3 and average dynamic viscosity of 5×10-4 lbf.s/ft2. Head loss in the nuclear reactor is 75 f..
Determine the mass flow rate of steam entering the turbine : Steam at 2000 psi and 1200 deg F enters a turbine operating at steady state. Partway through the turbine, 34% of the entering mass flow is extracted at 700 psi and 600 deg F. The rest of the steam exits the turbine as a saturated vapour at 1 psi. The..
What is the electrical power supply to the filament : The tungsten filament in a lamp has a diameter of 0.003 in and is 6-in long. When it is maintained at 2900K, what is the amount of energy emitted by the filament if the emissivity of the filament is 0.3? If the surroundings are at 20oC, what is the e..
Determine the heat flux across the steel sheet : A 10 mm thick Teflon sheet is perfectly bonded to a large 9 mm thick type 316 stainless steel sheets. The interface is at 119?C and the outer surface of the steel sheet is at 120?C. Take K Teflon = 0.25W/m.K K 316 Steel = 13.4 W/m.K In steady state, ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the incidence it of the tailplane for trim if the

calculate the incidence it of the tailplane for trim if the elevator deflection e is zero. ii calculate the neutral

  Module fea - finite element analysisnbspquestion 2 method

module fea - finite element analysisnbspquestion 2 method to assess the value of your analysis outputnbspa what is the

  If the scale graduations were printed on the tape under

a long steel tape measure 9.5 mm wide x 0.20 mm thick having an elastic modulus e 210 gpa is used to measure the width

  What is the power requirement of the compressor

Methane gas is compressed at the rate of 3x104 m3/hr (as measured at 0.1013 MPa and 15C) from 0.69 MPa and 26.7C to 3.45 MPa. The compressor operates adiabatically and has an efficiency of 80%. After compression, the methane is colled at a constant p..

  The system undergoes a polytropic process resulting in the

a closed system contains 0.8 kg of air initially at 155 kpa with a volume of 0.45 m3. the system undergoes a polytropic

  The final state is the critical point a on p-v and t-v

a liquid-vapor mixture of h2o at 2 mpa is heated in a constant volume process. the final state is the critical point. a

  A gas within a piston-cylinder assembly undergoes a

a gas within a piston-cylinder assembly undergoes a thermodynamic cylce consisting of three processes. process 1-2

  An aluminum thin-walled cylinder is 40 mm id inner diameter

an aluminum thin-walled cylinder is 40 mm id inner diameter by 50mm od outer diameter and is subjected to an internal

  A solar hot-water system stagnates at 85 c under

a solar hot-water system stagnates at 85 c under insolation of 740 wm2 and an ambient temperature of 17 c. find its

  Compute the shaft-power output and isentropic efficiency

steam flows through a small steam turbine at the rate of 10000 kgh entering at 600oc and 2.0 mpa and emerging at 0.01

  On the apollo 14 mission to the moon astronaut alan shepard

on the apollo 14 mission to the moon astronaut alan shepard hit a golf ball with a golf club improvised from a tool.

  Sketch the shear force and bending moment diagrams for the

a beam of square cross section bd20cm is 2 m long and simply supported at both ends. it carries a 100 n point load

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd