Because of inspection limitation the smallest crack that

Assignment Help Mechanical Engineering
Reference no: EM13613902

Two materials A and B of the same density are being considered for the design of a large plate that is 2 m wide and 3 m long. A maximum tensile load of 4.5 MN will act perpendicular to the 2 m dimension and consideration must be given to the possibility of pre-existing cracks. For this problem, failure can be defined as either gross yielding or fracture. In this case, through thickness cracks at the center of the plate and perpendicular to the applied load are of major concern. Because of inspection limitation, the smallest crack that can be detected is 2.54 mm.

Based upon the above consideration, which material would you recommend if the plate is to be of minimum weight?

Given:


Material A

Material B

KIC

115 MPa.m1/2

55 MPa.m1/2

?ys

910 MPa

1035 MPa

Reference no: EM13613902

Questions Cloud

Blood type ab is found in only 3 of the populationdagger if : blood type ab is found in only 3 of the populationdagger. if 205 people are chosen at random find the probability of
For the same power as in part a what is the maximum outside : a heat pump heats a house in the winter and then reverses to cool it in the summer. the interior temperature should be
In this case the line breaks when the kinetic energy of the : an electrically neutral model airplane is flying in a horizontal circle on a 2.0-m guideline which is nearly parallel
As a result each object experiences an electrostatic force : two spherical objects are separated by a distance of 1.41 times 10-3 m. the objects are initially electrically neutral
Because of inspection limitation the smallest crack that : two materials a and b of the same density are being considered for the design of a large plate that is 2 m wide and 3 m
The plane is in a 14 wind blowing toward the southwest : the nose of an ultralight plane is pointed south and its airspeed indicator shows 32 . the plane is in a 14 wind
At time t2 900 s a half-revolution later its velocity is : a cat rides a merry-go-round while turning with uniform circular motion. at time t1 2.00 s the cats velocity is v1
A cascade system using two ideal refrigeration cycles is : in cooling situations where the desired temperature range is large two refrigeration cycles can be stacked to create a
An article in the 1993 volume of the transactions of the : an article in the 1993 volume of the transactions of the american fisheries society reports the results of a study to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd