A cascade system using two ideal refrigeration cycles is

Assignment Help Mechanical Engineering
Reference no: EM13613899

In cooling situations where the desired temperature range is large, two refrigeration cycles can be stacked to create a cascading refrigeration system that increases the cooling capacity compared to a single-cycle system. A cascade system using two ideal refrigeration cycles is used. The high-temperature cycle uses Refrigerant-134a with saturated liquid leaving the condenser at 40C and saturated vapor leaving the heat exchanger at -20C. The low-temperature cycle uses Refrigerant-23, which is suitable for use in the colder temperature conditions. Refrigerant-23 leaves the evaporator as a saturated vapor at -80C with h = 330 kJ/kg, saturated liquid leaves the heat exchanger at -10C with h = 185 kJ/kg, and the fluid leaves the compressor with h = 405 kJ/kg.

a.) Determine the ratio of the mass flow rates for the two cycles.

b.) Determine the coefficient of performance for the overall system.

Reference no: EM13613899

Questions Cloud

As a result each object experiences an electrostatic force : two spherical objects are separated by a distance of 1.41 times 10-3 m. the objects are initially electrically neutral
Because of inspection limitation the smallest crack that : two materials a and b of the same density are being considered for the design of a large plate that is 2 m wide and 3 m
The plane is in a 14 wind blowing toward the southwest : the nose of an ultralight plane is pointed south and its airspeed indicator shows 32 . the plane is in a 14 wind
At time t2 900 s a half-revolution later its velocity is : a cat rides a merry-go-round while turning with uniform circular motion. at time t1 2.00 s the cats velocity is v1
A cascade system using two ideal refrigeration cycles is : in cooling situations where the desired temperature range is large two refrigeration cycles can be stacked to create a
An article in the 1993 volume of the transactions of the : an article in the 1993 volume of the transactions of the american fisheries society reports the results of a study to
Use n9 and p08 to complete parts a through c below find the : use n9 and p0.8 to complete parts a through c belowa find the probabilities and construct a binomial probability
What angle acompensates for the wind such that the shell : a fireworks shell is launched vertically from point a with speed sufficient to reach a maximum altitude of 500 ft. a
At the end of the year 2007 the inventory wasunderstated by : boswell electric prepared the following condensedincome statements for two successive

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd