Assuming maximum depth od the lake is less than 400 meters

Assignment Help Mechanical Engineering
Reference no: EM13623002

NASA is designing a mission to explore titan, the largest moon of Saturn. Titan has numerous hydrocarbon lakes containing a mix of methane and ethane in unknown proportions. A small submersible vehicle will exlpore Kraken Mare, the largest lake. Assuming maximum depth od the lake is less than 400 meters how much pressure in atmospheres must the submersible be designed to withstand? Assume surface tension is 147 kilopascals, surface temp is 94 Kelvin and gravity is 1.35 m/s^2.

The specific gravity of liquid methane is 0.415 and specific gravity of liquid ethane is 0.546?

Reference no: EM13623002

Previous Q& A

  A stock had returns of 12 percent 16 percent 10 percent 19

a stock had returns of 12 percent 16 percent 10 percent 19 percent 15 percent and -6 percent over the last six years.

  Monatomic molecules adsorbed on a surface are free to move

monatomic molecules adsorbed on a surface are free to move on this surface and can be treated as a classical ideal two

  Using the capital budgeting framework discussed in this

using the capital budgeting framework discussed in this chapter explain the sources of uncertainty surrounding a

  Describe a scenario where you believe a binomial

describe a scenario where you believe a binomial distribution would be appropriate. describe a scenario where you

  If the packing material experiences a maximum compression

a piece of electronic equipment that is surrounded by packing material is dropped so that it hits the ground with a

  For how long should matt expose a second plate located 58m

in astronomy it is common to expose a photographic plate to a particular portion of the night sky for quite some time

  You recently purchased a stock that is expected to earn 30

you recently purchased a stock that is expected to earn 30 percent in a booming economy 9 percent in a normal economy

  To determine the mass-transfer coefficient of chlorine in

silicon tetrachloride sicl4 is a key chemical in the silicon chemical vapor deposition. it is used in the production of

  Why should capital budgeting for subsidiary projects be

why should capital budgeting for subsidiary projects be assessed from the parents perspective? what additional factors

  Assess bas balance sheet as well as any comments in its

use bank of america ba 2012 annual report to answer the following questions1. what are the types of deposits that ba

Reviews

Write a Review

 

Similar Q& A

  Determine the rate of heat loss from the molten salt

Determine the rate of heat loss from the molten salt per meter length of the pipe.

  The liquid condensate is removed from the system at 60o f

atmospheric air at 90o f and 60 relative humidity flows over a cooling coil at an inlet volumetric flow rate of 2000

  Initially the pressure and volume of the gas is 200 kpa and

a gas behaves such that the product of its pressure and volume is constant pvc. initially the pressure and volume of

  Determine the largest allowable value of p if the shear

two forces each of magnitude p are applied to the wrench. the diameter of the steel shaft ab is 15mm. determine the

  If w1kn determine the force for supporting memebers ac ab

a boom for a crane is shown in the horizontal position. if w1kn determine the force for supporting memebers ac ab ad

  Find the temperature of source and sink

a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.

  A new prototype proven to perform with an isp of 1000s but

when deciding what propulsion system is most appropriate for a mission thrust and isp are not the only parameters that

  Determine the temperatures of surface 1 through 4 of the

determine the temperatures of surface 1 through 4 of the furnace cavity of example 13.3 if the entire furnace

  An ideal otto cycle heat engine with compression ratio 151

an ideal otto cycle heat engine with compression ratio 15.1 assume perfects gases with constant specifics heat. heat

  Determine a the temperature of the refrigerant exiting the

refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady

  Te acceleration due to gravity at sea level is g 981 ms2

the acceleration due to gravity at sea level is g 9.81 ms2 . what is the persons weight at sea level? the acceleration

  Determine the normal stress

If the bar is subjected to centric forces of magnitude P = 30 kN and knowing that EA = 70 GPa and EB = 105 GPa, determine the normal stress (a) in the aluminum layers, (b) in the brass layer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd