Airline terminal problem by adding agent breaks

Assignment Help Other Engineering
Reference no: EM13338658

Modify the airline terminal problem by adding agent breaks. The 16 hours are divided into two 8-hour shifts. Agent breaks are staggered (i.e., one agent goes on break, and immediately upon return, the next agent goes on break, until all agents have had their breaks), starting at 90 minutes into each shift. Each agent is given one 15-minute break.

Agent lunch breaks (30 minutes) are also staggered, starting 3.5 hours into each shift. The agents are rude and, if they are busy when break time comes around, they just leave anyway and make the passenger wait until break time is over before finishing up that passenger (since all agents are identical, it is not necessary for the same agent to finish up that passenger).

Compare the results of this model to those of the model without agent breaks. Use the "Station" and "Route" modules to help you in the animation. Use the "Variable" icon to monitor and identify the metrics requested.

Reference no: EM13338658

Questions Cloud

How long would it take for the box to rise in potential : Consider a black box which is approximately a 10-cm cube with two binding posts. Each of these terminals is connected by a wire to some external circuits. Otherwise, the box is well insulated from everything.
Calculate the angular velocity of the second hand : While sitting in physics class one day, you begin to ponder the workings of the analog clock on the classroom wall. Calculate the angular velocity of the second hand
What is the maximum rate of energy transformation : A mass on a spring with constant 3.63 N/m vibrates with position given by the equation x = (5.00 cm) cos(3.10t rad/s). What is the maximum rate of energy transformation
Psychoanalytic and person-centered therapy : Psychoanalytic and person-centered therapy have two different philosophies about what motivates a person's behavior. Which do you prefer, determinism (your thoughts, feelings, and behaviors are mostly unconscious and a result of past experiences) or ..
Airline terminal problem by adding agent breaks : Compare the results of this model to those of the model without agent breaks. Use the "Station" and "Route" modules to help you in the animation. Use the "Variable" icon to monitor and identify the metrics requested.
Concepts and rapeutic process of existential therapy : Describe the key concepts and the rapeutic process of Adlerian theory and therapy. Describe the key concepts and therapeutic process of existential therapy. Compare and contrast the rationale of the two therapeutic approaches for explaining psycholog..
What is the speed of electrons in the beam : Early black-and-white television sets used an electron beam to draw a picture on the screen. What is the speed of electrons in the beam
What are tax concepts involved in completing schedule : What are the tax concepts involved in completing the Schedule A and Form 2441 and what are the tax planning considerations you took into account while completing the Schedule?
Eligible shareholders of an s corporation : Which if any of the following can be eligible shareholders of an s corporation?

Reviews

Write a Review

Other Engineering Questions & Answers

  Describe and compare the ventilation systems

State reasons for the popularity of decline mining in modern operations. What factors need to be taken into account in deciding the cut off depth beyond which shaft operations should be used instead of decline access.

  What is the martensitic phase transformation

What is the tempering treatment typically applied to martensitic steels. (iv) Briefly, discuss by defining, comparing and contrasting gray and white cast irons.

  Project management for engineering

economic feasibility of the projec, restrictions are the economics of the project based,  technical feasibility for the project

  Thin, thick and combined cylinder theory

Strength of Materials: Advanced DV01 35, LO2 Thin, Thick and Combined Cylinder Theory:  This outcome is assessed using all three of the assignments detailed below.   For each assignment you are required to write a report.

  Formulate a maximum-flow problem

Formulate a maximum-flow problem that will determine the maximum number of people that can travel to the safe facilities

  Production data analysis

Objective of this task is to collect and obtain information on variables of interest in a systematic way to prepare the required data for studying the decline rates of Bakken wells.

  Design and detail the tension reinforcement

The L-beam illustrated in Figure is to carry, in addition to its own weight, a dead load g = 25 kN/m and a live load q = 100 kN/m over a simply-supported span of 8 m. Design and detail the tension reinforcement.

  What would the maximum possible voltage be

If the total range of voltages started at zero and there are 512 intervals, what would the maximum possible voltage be?

  Calculate the volumetric flow rate

Calculate the volumetric flow rate and the mass flow rate and determine the average flow velocity of the air and the air quantity flowing

  What is the overhead of a ds1 frame that uses bit robbing

Some home ISDN "modems" will combine two BRI channels together. What would the data rate be if you could use both channels simultaneously for data transmission?

  What would be stakeholders in a project

What would be stakeholders in a project

  Ten factors to be considered when assessing the health risks

Outline at least ten factors to be considered when assessing the health risks from exposure to solvents in a factory producing home furniture with a range of painted and varnished finishes

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd