A mass of 24 kg of air at 150 kpa absolute and 12 degrees

Assignment Help Mechanical Engineering
Reference no: EM13343955

A mass of 2.4 kg of air at 150 Kpa absolute and 12 degrees Celsius is contained in gas tight, frictionless piston cylinder device. The air now compressed to a final pressure of 600kPa abs. During the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the .ork input during this process. R(air)=287j/KgK 

Reference no: EM13343955

Questions Cloud

Design an autonomous vehicle that can enter a room through : design an embedded system that will include four ultrasonic range finders - assume these have 10m range one 3-axis
A 50g sample of a hydrate of cacl2 was heated and only 43 g : a 5.0g sample of a hydrate of cacl2 was heated and only 4.3 g of the anhydrous salt remained. what is the percentage of
Calculate the static thrust of the turbojet engine having : calculate the static thrust of the turbojet engine having mass flow 88lbmsec the ratio of air and fuel mass flowing
How many grams of ammonium sulfate can be produced in 30 : how many grams of ammonium sulfate can be produced in 30 mol of h2so4 react with excess nh3 according to the equation
A mass of 24 kg of air at 150 kpa absolute and 12 degrees : a mass of 2.4 kg of air at 150 kpa absolute and 12 degrees celsius is contained in gas tight frictionless piston
What is the volume of dry gas at standard conditions the : if 77.0 ml of hydrogen gas is collected over water at 50.0 degrees celsuis and 763 mm hg what is the volume of dry gas
Calculate the mass of oxygen in mg dissolved in a 500 l : calculate the mass of oxygen in mg dissolved in a 5.00 l bucket of water exposed to a pressure of 1.13 atm of air.
A 140 g sample of cacl2 is dissolved in 121 g of water with : a 14.0 g sample of cacl2 is dissolved in 121 g of water with both substances at 25.0degc. calculate the final
The manometer shown above in problem 1 above contains water : the manometer shown above in problem 1 above contains water and kerosene. with both tubes open to the atmosphere the

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  What is the average friction factor in the duct

Air enters an adiabatic duct of L/D = 40 at V1 = 170 m/s and T1 = 300 K. The flow at the exit is choked. What is the average friction factor in the duct?

  Find the value of the gain

Using MATLAB Simulink, set up the negative feedback system of and find the value of the gain

  A hot dog can be considered to be a cylinder 12 cm long and

a hot dog can be considered to be a cylinder 12 cm long and 2 cm in diameter whose properties are rho 980 kgm3 cp 3.9

  How long will it take the puck to slow down to a speed

how long will it take the puck to slow down to a speed of 1m/s and how long will it take for the puck to stop completely? How far will the puck travel before it slows to 1m/s? You can assume the table is very very long.

  Determine the corresponding angular velocity of gear b

Gear A rotates with an angular velocity of 100 rpm clockwise. Knowing that the angular velocity of arm AB is 50 rpm counterclockwise, determine the corresponding angular velocity of gear B.

  Compute the steady state excess electron

Calculate the steady state excess electron and hole concentrations as a function of distance into the semiconductor.

  Determine the maximum torque t

a shaft is made of a steel alloy having an allowable shear stress of 12 ksi. If the diameter of the shaft is 1.5 in., determine the maximum torque T that can be transmitted. What would be the maximum torque T' if a 1 in. diameter hole is bored thr..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the stress in each of the wires

a 1.5 ton crate is hoisted by three steel wires. Each wire is 1/4 in in diameter and each wire carries one-thired of the load. Determine the stress in each of the wires.

  Find the tension in ropes a and b

a 100 pound ball is suspended from a wall by a rope that is pulled asided by a horizontal rope B and held so that rope A makes a angle of 30 degrees with the vertical wall. Find the tension in ropes A and B?

  Determine the natural frequencies of the system

Determine the natural frequencies of the system. For the baseline system I get natural frequencies at the following engine speeds: 435, 2026, 2818, 5225, 7093, 10245, and 12153 rpm.

  Determine angle theta degrees that requires minimum torque

Determine the angle theta degrees that requires the minimum torque T to keep the seam closed. (Hint: use Mohr's circle). Give the answer in degrees.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd