User Account

All Pages

A light pressure vessel is made of 2024-t3 aluminum alloy

Assignment Help Mechanical Engineering
Reference no: EM13626663

A light pressure vessel is made of 2024-T3 aluminum alloy tubing with suitable end closures. This cylinder has a 3.50 in. OD, a 0.065 in. wall thickness, and ν = 0.340. The purchase order specifies a minimum yield strength of 46 kpsi. Using the distortion-energy theory, determine the factor of safety if the pressure-release valve is set at 500 psi?

Reference no: EM13626663

Questions Cloud

An artist sells her works at the east lansing art festival : an artist sells her works at the east lansing art festival. suppose that 5 of those who stop by her booth will buy a
Air is compressed by a 30-kw compressor from p1 to p2 the : air is compressed by a 30-kw compressor from p1 to p2. the air temperature is maintained constant at 25 degrees c
A steady flow compressor is used to compress air from 1 atm : a steady flow compressor is used to compress air from 1 atm 25ordmc to 8 atm in an adiabatic process. the compressor
Approximately what proportion of the area under a normal : approximately what proportion of the area under a normal curve with mean ? and standard deviation ? falls to the right
A light pressure vessel is made of 2024-t3 aluminum alloy : a light pressure vessel is made of 2024-t3 aluminum alloy tubing with suitable end closures. this cylinder has a 3.50
How many standard deviations from the mean would a car : john beale of stanford ca recorded the speeds of cars driving past his house where the speed limit read 20 mph. the
A 05 m3 tank contains air at 300 k and 075 mpa a valve is : a 0.5 m3 tank contains air at 300 k and 0.75 mpa. a valve is suddenly opened and air rushes out until the tank pressure
A student is standing at the edge of a rotating circular : a student is standing at the edge of a rotating circular platform of mass 200kg and radius 1.1 m. the student of mass
Find the standard deviations of the random variable options : find the standard deviations of the random variable. options a 6 b 7 c 10 d

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  An ammonia absorption refrigeration cycle requires 2500

an ammonia absorption refrigeration cycle requires 2500 btulbm heat transfer in the generator.saturated vapor leaves

  A computer cpu chip operates at steady state with d-c

a computer cpu chip operates at steady state with d-c electrical input of 4.5 amps at 9 volts. to prevent the chip from

  Calculate the mass of mixture produced at the mixing stage

calculate the mass of mixture produced at the mixing stage, the mass jam produced from the kettle and the mass od water evaporated from the kettle.

  Calculate the pressure of methane gas

Calculate the pressure of 15.0g of methane gas in a 1.50L vessel at 45.0 degrees C using (a) the Ideal Gas Law and (b) the van der Walls equation using the following information about the constants, a and b: a = 2.253 and b = 0.04278.

  Determine the temperature of the surface of the spacecraft

the outer surface of a spacecraft has an emissivity of 0.8 and an absorptivity of 0.3 for solar radiation. if solar

  In each case calculate the biot number for the object and

in each case calculate the biot number for the object and indicate whether or not the lumped approximation is valid.a a

  The 6 x 12 in timber beam has been strengthened by bolting

the 6 x 12 in timber beam has been strengthened by bolting to it thenbsp5 x ? in steel reinforcement shown. the modulus

  Use your equation to calculate the pressure in mb at 1200 m

assume that in a certain area the atmospheric lapse rate ?gamma subscript actual is equal to zero from the ground up to

  Methane at 6 mpa and 245 k is heated at a constant

methane at 6 mpa and 245 k is heated at a constant pressure until its volume has increased by 90 percent. determine the

  After pumping stops and a new equilibrium is reached the

after pumping stops and a new equilibrium is reached the tire pressure is 600 kp a and the air temperature in the tire

  Determine the velocity of the airplane required for pilot

Determine the velocity of the airplane required for pilot to experience weightlessness at the top of the circular path.

  Problem on kinematic chains

Assignment on kinematic chains - Type of chain whether it is locked,constrained or unconstrained?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd