A 05 m3 tank contains air at 300 k and 075 mpa a valve is

Assignment Help Mechanical Engineering
Reference no: EM13626661

A 0.5 m^3 tank contains air at 300 K and 0.75 MPa. A valve is suddenly opened and air rushes out until the tank pressure drops to 0.15 MPa. The air in the tank at the end of the process may be assumed to have undergone a reversible, adiabatic process. Determine the final temperature (K) and mass (kg) in the tank.

Reference no: EM13626661

Questions Cloud

A steady flow compressor is used to compress air from 1 atm : a steady flow compressor is used to compress air from 1 atm 25ordmc to 8 atm in an adiabatic process. the compressor
Approximately what proportion of the area under a normal : approximately what proportion of the area under a normal curve with mean ? and standard deviation ? falls to the right
A light pressure vessel is made of 2024-t3 aluminum alloy : a light pressure vessel is made of 2024-t3 aluminum alloy tubing with suitable end closures. this cylinder has a 3.50
How many standard deviations from the mean would a car : john beale of stanford ca recorded the speeds of cars driving past his house where the speed limit read 20 mph. the
A 05 m3 tank contains air at 300 k and 075 mpa a valve is : a 0.5 m3 tank contains air at 300 k and 0.75 mpa. a valve is suddenly opened and air rushes out until the tank pressure
A student is standing at the edge of a rotating circular : a student is standing at the edge of a rotating circular platform of mass 200kg and radius 1.1 m. the student of mass
Find the standard deviations of the random variable options : find the standard deviations of the random variable. options a 6 b 7 c 10 d
Air enters the compressor section of a turbojet engine at : air enters the compressor section of a turbojet engine at 15 c and 0.1 mpa at a rate of 100 m3min. the air leaves at
The mean number of errors per page made by a clerk in the : the mean number of errors per page made by a clerk in the word processing pool of a bank is thought to be 2.8 with the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  With the piston face resting against the stops the water

a piston-cylinder assembly is fitted with stops. the assembly contains 0.1 kg of water initially at 1 mpa and 500degc.

  Cn the final equilibrium state be determined how many

consider a rigid tank with a partition such that there are two equal volumes which are known. on one side has water at

  Derive an expression for the bounding energy eo in terms of

the net potential energy en between two adjacent ions is sometimes represented by the expression en -cr d exp-rpin

  Determine a the pressures in kpa and temperatures in k at

from fundamentals of engineering thermodynamics book 9.85 for the turbojet in problem 9.84 plot the velocity at the

  Determine the largest mass m

the pin c will support a force of 24 knmagnitude.Based on this criterion, you are asked to determine the largest mass m that the frame can safely support.the diameter of pulley at d is given as 0.2 m.find maximum mass m that can be supported by fr..

  Use work and energy to determine the center of mass

bar ab of mass m and mass moment of inertia i 112ml2 is constrained to move within the channel as shown. the bar is

  The total horizontal force exerted by the planes engine is

jus before it lifts off a 10500 kg airplane is traveling at 60 fts. the total horizontal force exerted by the planes

  How does the statistical mechanical definition of entropy

how does the statistical mechanical definition of entropy allow a reinterpretation of the second and third law of

  A flow of 305 kgmin of water from a hot water tank at 51oc

a flow of 30.5 kgmin of water from a hot water tank at 51oc is mixed with a 29.1 kgmin flow of 20oc water. determine

  An irregularly shaped object weighs 100 lb in air and 64

an irregularly shaped object weighs 100 lb in air and 64 lb when fully submerged in water. determine the volume and

  A 15-tooth pinion having a pressure angle of 25ordm and

a 15-tooth pinion having a pressure angle of 25ordm and module of 8mm is to drive an 18-tooth gear. determine for both

  Determine an appropriate summertime indoor design

determine an appropriate summertime indoor design temperature for an exercise area located within an office complex.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd