User Account

All Pages

A dam across a river dams up a lake 300 m higher than the

Assignment Help Mechanical Engineering
Reference no: EM13631260

A Dam across a river dams up a lake 300 m higher than the river downstream. The electric generators driven by water-powered turbines deliver 1600 MW of power. If the water is 19.5 degree C,

1) Find the pressure applied to the turbine

2) Find the min. amount of water that is running through the turbines.

3) If the water comes out from a pipe with a radius 50 cm. What would be the speed of the water coming from the pipe?

Reference no: EM13631260

Questions Cloud

Draw the p-v and t-s diagrams of the cycle and determine a : a variable specific-heat air cycle in a closed system is composed of the following four processesprocess 1-2 isentropic
Fine pearlite and a small amount of martensite are found : fine pearlite and a small amount of martensite are found in a quenched 1080 steel. what microstructure would be
The gas may be considered idal at these conditions find : two cubic feet 2 ft3 of air is compressed slowly from 1 atm and 80 degrees f to a pressure of 10 atm. the gas may be
Aditional heat is added until the pressure reaches 12 mpa : two kilograms of water are contained in a pistoncylinder arrangement. the massless piston is loaded with a linear
A dam across a river dams up a lake 300 m higher than the : a dam across a river dams up a lake 300 m higher than the river downstream. the electric generators driven by
The vessel will rupture if the pressure reaches 5 mpa what : 15 kilograms of water are confined in a rigid vessel with a volume of 0.5 m3 with an intitial temperature of 50
A beam of 800 kev gamma is mormally incident on a sheet of : a beam of 800 kev gamma is mormally incident on a sheet of lead 12mm thick. the rate of energy transmission is 3x105
An 8-m long unisulated square duct of cross sectional 02-m : an 8-m long unisulated square duct of cross sectional 0.2-m x 0.2-m and relative roughness 10-8 passes through the
Find the specific volume of steam in m3kg at 25 mpa and : find the specific volume of steam in m3kg at 2.5 mpa and 283 degrees c. what is the value predicted by the ideal gas

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  One of the problems of wind tunnel testing at airspeeds

one of the problems of wind tunnel testing at airspeeds near sonic speed is the large effect on the flow conditions of

  If a strain of -0087 is measured by a strain gage what

a bar of aluminum is subjected to a tensile load of 15000 lbs. if the bar is 0.35 inches in diameter and 20 inches long

  Consider 25 of austenite containing 065 wt c and cooled to

consider 2.5 of austenite containing 0.65 wt c and cooled to below 727 degrees c.a what is the proeutectoid phase?b how

  The outer surface of the heater is exposed to a fluid with

a very thin electric heater is wrapped around the outer surface of a long cylindrical tube whose inner surface is

  4 kgs of saturated liquid water is heated in a steam

4 kgs of saturated liquid water is heated in a steam boiler at 2 mpa to an outlet temperature of 250 c. determine the

  Calculate the work input during this process

During the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the work input during this process. R(air)=287j/KgK

  Determine the radiosity at the top plate surface the net

the top surface of an l 5-mm-thick anodized aluminum plate is irradiated with g 1000 wm2 while being simultaneously

  Alternative methods for casting the concrete for the wall

Compare the time and cost of using the following three alternative methods for casting the concrete for the wall: 1) direct chute 2) pumped 3) crane and bucket.

  In a constant-pressure process steam at a 100 psia is

in a constant-pressure process steam at a 100 psia is presented to the piston of a pump and causes it to travel 3 in.

  Minimum weight design of a variable shape three-bar truss

Obtain a new solution, and determine whether any buckling constraints are active. If no buckling constraints are active for L = 10 in., re-run the analysis by increasing L , and estimate the value of L at which at least one buckling constraint b..

  If the probe surface has an emissivity of 085 and the probe

a sphereical interplanetary probe of 0.6-m diameter contains electronics that dissipate 170 w. if the probe surface

  What are the forces acting on workpiece

What are the forces acting on workpiece during turning process. how workpiece should be clamp

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd