A bar of the cross section is shown in figure 3 and is made

Assignment Help Civil Engineering
Reference no: EM13383418

A bar of the cross section is shown in Figure 3 and is made of steel that is assumed to be elastoplastic with E=200GPa and σ
y=240 MPa. For the bending about the z-axis, determine the bending moment at which (a) yield first occurs, and (b) the plastic zones at the top and bottom of the bar are 20 mm thick. 

Reference no: EM13383418

Questions Cloud

Calculate the concentration of co ppm in the stack : a mixture of 70 mole propane and 30 mole hydrogen is burned with 30 excess air. fractional conversions of 90 of the
Calculate the final temperature when a 204 gram sample of : calculate the final temperature when a 20.4 gram sample of ice at 0oc is placed into a styrofoam cup containing 111
The addition of 6 g of salt to a sample of pure water : the addition of 6 g of salt to a sample of pure water causes its freezing point to be reduced from 0degc to -1.5degc.
Cadmium ion in solution is analyzed by precipitation as the : cadmium ion in solution is analyzed by precipitation as the sulfide a yellow compound used as a pigment in everything
A bar of the cross section is shown in figure 3 and is made : a bar of the cross section is shown in figure 3 and is made of steel that is assumed to be elastoplastic
Explain how the desert air can contain much more h2o vapor : 1.explain how the desert air can contain much more h2o vapor in the air than the pole and still a lower humidity than
An elevator drive sheave of diameter 1 m and negligible : an elevator drive sheave of diameter 1 m and negligible mass is mounted on a shaft midwaynbspbetween bearings which are
Carbon dioxide at 223degc and 45 atm flows into the reactor : urea h2nconh2 is used extensively as a nitrogen source in fertilizers. it is produced commercially from the reaction of
Three different materials designated a b and c are tested : three different materials designated a b and c are tested in tension using test specimens having diameters of 0.755 in.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the upstream depth-y1 of the hydraulic jump

The heated water outflow from a nuclear power plant is cooled in a 50-m wide rectangular channel that has a discharge, Q = 225.0 m3/s. The Manning's n is 0.015 and the bed slope is 5.0x10-4

  Compare cost of electric heater to deliver the same energy

A household uses 10 therms of natural gas per month in a gas furnace for heating at a cost of $1.00/therm. For an electric heating system the cost of electricity is $0.10/kwh. Compare the cost of the electric heater to deliver the same energy as t..

  Find the tension in the cord when the radius is given

The ball is kicked so that it has a velocity of 0.5 m/s and the cord is pulled in at a rate of 0.2 m/s. Neglect friction so that the only important force on the ball is the tension in the cord. Find the tension in the cord when the radius is 0.25 ..

  Determine what should the after burner temperature be

An afterburner has been selected to destroy 99.9% of the ethane (CH3-CH3)in a gas (mostly air) stream . if the residue time is 0.8 seconds and the pressure is 1.1 atmospheres in the after burner,

  Calculate what is the peak discharge at the reach outlet

Use the Muskingum method to route a flood through a reach a river. The base flow is 100 cfs, and the incoming flood flow increases 50 cfs every 2 hr over a 6 hr period and the subsides at the same rate.

  What are the speed and acceleration of the disks top

disk of radius R=7 in. spins at a constant angular speed of w=500rpm in the clockwise direction. If the disk is released from rest far above the ground, what are the speed and acceleration of the disk's top C point after it has fallen h=3ft

  Determine factor of safety of trench by the culmann method

A 1.5 meter deep vertical wall trench is to be cut in a soil whose unit weight is 17.36 kN/cubic meters, angle of internal friction is 25 degrees, and cohesion is 20.6 kN/square meters.

  Estimate the mean and standard deviation of time

The probability density function, f(t), of the time in hours between storms during the summer in Miami is estimated as f(t) = .014e^(-.014t) if x > 0, f(t) = 0  if x is less than or equal to 0 where t is the time interval between storms in hours.

  Explain how to estimate the flow rate in the cross section

The river channel itself is 20m wide and flow depth is 5m and the sandy bottom has an n=0.02, the left bank is 40m wide and the flow depth is 0.5m, while the right bank is 100m wide with a flow depth of 1m.

  Deytermine what is the penetration h for the pile

A pile resists the tension developed by three stay cables for a major for a tent (membrane) structure. Assuming no bending is desired in the pile (no resultant horizontal componenet),

  Find residual chemical concentration and amount of chemical

A chemical is added at the beginning of a water treatment plant at a dose of 750 lb/day. The water treatment plant provides water to a community of 200,000 people and the average water consumption in the city is 110 gallons per capita per day (gpc..

  Estimate the flow rate when draw down at the well

A fully penetrating well of 30 cm diameter in an unconfined aquifer of saturated thickness 50 m was found to give the following draw down - discharge relationship under equillibium condition.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd