4MA008 Engineering Science Assignment

Assignment Help Other Engineering

Reference no: EM132731567

4MA008 Engineering Science - University Of Wolverhampton

Electrical & Mechanical Engineering

QA1 (a) A battery has an open-circuit voltage of 12 V and a full-load rated current of 1 A. When a load resistance R is connected across it drawing the full rated current of the battery, the load voltage is found to be 11 V. Determine the internal resistance of the battery and its voltage regulation.

(b) Determine the resistance, at room temperature, of a copper wire having a diameter of 2.0 mm and a length of 500 m. You may assume that the resistivity of copper at room temperature is 1.72 x 10^-8 Ω.m .

(c) The circuit in Figure Q1 is a potential divider. Use Microsoft Excel, or any similar software, to plot the variation of the output voltage with variation in R2 over a suitable range.

Making any reasonable assumptions and modifications, explain how this circuit may be used as a darkness detector which can turn a mains-powered lamp automatically during darkness.

QA2 Refer to the circuit in Figure Q2 and given that:
R1 = 4 Ω, R2=2 Ω, R3=12 Ω, R4=6 Ω R5 = 5 Ω, R6=60 Ω, and R7=30 Ω

IS = 2 A and E1=12 V

Making any reasonable assumptions answer the following:

(a) Reduce the circuit to the left of terminals a-b to its Norton's equivalent circuit.

(b) Reduce the circuit to the right of terminals a-b to its Thevenin's equivalent circuit.

(c) A load resistance RL = 10 Ω is now connected between terminals a-b. Using parts (a) and (b) and the superposition principle, determine the current in the load resistance RL.

(d) Calculate the power dissipated in the load resistance and if the load remains connected for 5 minutes, calculate the electrical energy converted to heat in the load.

(e) Determine the value of the load resistance, which when connected between terminals a and b, will draw maximum power from the circuit and use Microsoft Excel, or any similar software, to plot a graph showing the variation in the power delivered to the load for a suitable range of the load resistance and Comment on your graph.

QA3 A series RLC circuit is connected across an AC voltage source of 230 V (rms) 50 Hz. Given that the resistance R is 30 ohms, the inductance L=100 mH, and C = 250 μ F :
(a) Calculate the impedance of the circuit and sketch the Z-triangle.
(b) Determine the magnitude and phase of the circuit current.
(c) Calculate the voltages across R, L and C and sketch a phasor diagram showing the circuit current and voltages.
(d) Calculate the circuit apparent power, true power and reactive power and sketch a labelled power triangle.
(e) Find the supply frequency that will allow the circuit to draw maximum current from the AC source. Explain, briefly, the significance of this frequency.

SECTION B

QB1 The link shown in figure QB1 is subjected to the forces F1 = 500 N and F2 = 350 N.
(a) Determine the magnitude of the resultant force.
(b) Determine the direction of the resultant force.
(c) Express both forces F1, F2, and the resultant force in vectorial notation

QB2.1 Figure QB2a shows the graph of the velocity trend with time, associated with a car in rectilinear motion.
(a) Determine the distance travelled after 50 s, and the distance travelled after 90 s.
(b) Determine the average velocity of the car.
(c) Determine the acceleration at the time instants t = 40 s and t = 70 s.

QB2.2 A ball is launched against a wall at an initial velocity v0 = 25 m/s with the inclination angle indicated in figure QB2b. The distance between the wall and the launch position is 22 m.
(a) Determine the total time between the instant at which the ball was launched and the instant at which the ball hits the wall.
(b) Determine the vertical distance (i.e. the height difference) from the launch position, at which the ball will hit the wall.
(c) Determine the horizontal and vertical components of the velocity at the time instant the ball hits the wall.
(d) Explain if, by the time the ball hits the wall, it has already passed from the point of maximum height of the trajectory, and why.

QB3.1 Figure QB3a shows a beam supported by two pin constraints at its ends, A and B, subjected to distributed loads as indicated.
(a) Sketch the free body diagram for this system, with clear indication of the reaction forces
(b) Determine magnitude and position of the equivalent concentrated loads corresponding to the distributed loads in each relative part of the beam, namely from 0 to 0.4 m (distance from A), from 0.4 m to 1.2 m, and from
1.2 m to 2 m.
(c) Determine the reaction forces in A and B, by solving the associated system of static equilibrium equations.
(d) Determine the internal forces at the section distant 1 m from A.

QB3.2 Consider now the beam loaded as shown in figure QB3b, with reaction forces already provided. Determine the equations of the shear load and moment T(x), M(x) along the beam length, and draw the relative diagrams.

Attachment:- Engineering Science.rar

Reference no: EM132731567

Questions Cloud

Project internal rate of return-the everett co : The Everett Co. is looking a project with an outlay of $829 which will have a positive cash flow at t = 3 of $1,087 with no other cash flows at t = 1 and t = 2.

Find assertions in relation to the purchases account : Find Which assertions in relation to the Purchases account does this procedure MOST directly address? The payables manager is required to inspect the purchase

What is sultan incorporated wacc : What is Sultan Incorporated's WACC (in percent to two places) if it has $15,622 with 9% after-tax cost of debt, $7,539 with 7% cost of preferred, and $10,521

What the role and business implications of digital corporate : What the Role and business implications of digital corporate financial reporting (e.g., XBRL technology), and evidence of impact on key stakeholders

4MA008 Engineering Science Assignment : 4MA008 Engineering Science Assignment Help and Solution, University Of Wolverhampton - Assessment Writing Service - Determine the internal resistance

What is the fair-value of a share : Assuming that after year 2, Omni's contract with the City of Detroit will give it a constant growth rate of 3%, what is the fair-value of a share if the require

Which of the causes a market to be weak-form efficient : Which of the causes a market to be weak-form efficient? Investors analysing past prices and buying shares they think are more likely to increase than decrease

What is the black model price of a european call option : What is the Black model price of a European call option on this futures contract, expiring on December 20 and with an exercise price of $46?

How many shares would have been issued from bond conversion : You learn from his notes in the new file that FixAll had issued 28,500. How many shares would have been issued from the bond conversion of July 1, 2023?

User Account

All Pages