User Account

All Pages

Peak amplitude measurement

Assignment Help Electrical Engineering
Reference no: EM13865304

When carrying out an FFT of a cosine wave whose frequency is 0.1Hz and whose amplitude is unity , explain why the peak amplitude measurement obtained in the range 0.09Hz to 0.11Hz should be 0.5

Reference no: EM13865304

Questions Cloud

Cross-correlation analysis : A radar transmits a signal (st) to detect aircrafts nearby. The signal sr1 is received when there is an aircraft and the signal sr2 is received where is no aircraft in radar's range.
Should pankratz error be excusted why or why not : Critical Legal Thinking - Should Pankratz's error be excusted? Why or why not? Ethics- Did either party act unethically in this case? Was this a legitimate legal dispute
Difference between adaptive expectations and rational expect : What is the difference between adaptive expectations and rational expectations?
What is probability that none of the people are independent : What is the probability that none of the people are Independent? What is the probability that fewer than five people are Independent? What is the probability that more than two people are Independent?
Peak amplitude measurement : When carrying out an FFT of a cosine wave whose frequency is 0.1Hz and whose amplitude is unity , explain why the peak amplitude measurement obtained in the range 0.09Hz to 0.11Hz should be 0.5
Expectations of inflation result in clockwise phillips loops : How can adaptive expectations of inflation result in clockwise Phillips loops? Why would these loops not be completely regular?
Analysis and design of beam : A 2nd level floor system of an office block is made up of a 125 mm thick slab cast monolithically with stiff beams which are spaced L3 (centre-to-centre) as shown in Figure 1.
A vertical short run aggregate supply curve have for the eff : What implications would a vertical short run aggregate supply curve have for the effects of demand management policy?
Differentiate between various theoretical explanations : Differentiate between various theoretical explanations for delinquent behavior.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Compute the amount of time required to deliver

Compute the amount of time required to deliver 10 frames to the receiver with stop-and-wait flow control. Assume that all frames and ACKs are received correctly.

  What size of capacitor must be use in order to avoid penalty

A certain load takes 10kW at 0.5pf lagging when connected to a 230V, 60Hz source. The supply company charges a penalty when the power factor fall below 0.8. What size of capacitor must be used in order to avoid penalty

  Design op amp circuit to produce output vout

design op amp circuit to produce output vout which is related to inputs v1, v2 and v3 by expression vout= -(3v1+5v2+8v3). assume max permitted resistor value= 200k. use only one op amp

  Calculate the electric field intensity at a distance

Calculate the electric field intensity at a distance 'd' along the z-axis in terms of a,b,c, and d. Explain your reasoning. This result should be analytic.

  Determine what is the output signal to noise ratio

Signal w(t) is input to the filter. This signal is white noise, with PSD = N0/2. If we denote the filter output as n(t), what is the power in n(t) We input v(t) + w(t) into the filter, where v(t) = Ac cos(2pif0t). If Ac=4, what is the output signal..

  Design a non-uniform linear array to have the pattern

A 3-element uniform linear array with inter-element spacing of λ/2 is operated as a broadside array ,find the directions of null radiation , find the direction and the relative level of the side lobe .

  Determine what is the voltage across the capacitor

A voltage source is in series with a 1 MΩ resistor and a100 picofarad capacitor. The voltage source is 10cos(2π*10^3t - π/6). What is the voltage across the capacitor

  Define what is correct symbol rate pulse rate for link

What is correct symbol rate (pulse rate) for this link? What is the bit rate with BPSK modulation? What is the bit rate with QPSK modulation?

  Angle modulation and detection

State Carson's rule for bandwidth estimation. What does it reduce to for NBFM and WBFM and d erive an time domain expressionfor the output xd(t) of the system

  What is magnitude of the current if effective current given

Calculate the following: A. What is the magnitude of the voltage in a wall socket if the effective voltage is 240 Vrms B. What is the magnitude of the current if the effective current is 360 mA rms

  As was mentioned the one-way bandwidth available to a

as was mentioned the one-way bandwidth available to a single operator in the amps system is 12.5 mhz with a channel

  Determine the insulation resistance of the cable

The insulation resistance of a kilometer of the cable having a diameter of 2 cm and an insulation thickness of 2 cm is600 ohms. if the thickness of the insulation is increased to 3 cm, find the insulation resistance of the cable.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd