As was mentioned the one-way bandwidth available to a

Assignment Help Electrical Engineering
Reference no: EM13344272

As was mentioned, the one-way bandwidth available to a single operator in the AMPS system is 12.5 MHz with a channel bandwidth of 30 kHz and 21 control channels. We would like to calculate the efficiency with which this system utilizes bandwidth for a particular installation. Use the following parameters:

Cell area = 8 km2.

Total coverage area = 4000 km2 Frequency reuse factor = 7 

Average number of calls per user during the busy hour =1.2

Average holding time of a call = 100 s

Call blocking probability = 2%

a. How many voice channels are there per cell?

b. Use Table 13.1 and a simple straight-line interpolation to determine the total traffic carried per cell, in Erlangs/cell. Then convert that to Erlangs/km2.

c. Calculate the number of calls/hour/cell and the number of calls/hour/km2.

d. Calculate the number of users/hour/cell and the number of users/hour/channel.

e. A common definition of spectral efficiency with respect to modulation, or modulation efficiency, in Erlangs/MHz/km2, is

ηm= (Total traffic carried by the system) / ((Bandwidth)(Total coverage area))

Determine the modulation efficiency for this system.

Reference no: EM13344272

Questions Cloud

How can i detect a cave entrance on a rocky cliff now : how can i detect a cave entrance on a rocky cliff now buried under 20 feet earth rocks by use of vertical electric
A 31 l tank contains a gas under a pressure of 617 atm what : a 31 l tank contains a gas under a pressure of 617 atm. what volume would the gas occupy at the same temperature at 900
A flask contains 0160 of liquid bromine determine the : a flask contains 0.160 of liquid bromine . determine the number of bromine molecules present in the
A graduated cylinder contains 154 of water a 150 piece of : a graduated cylinder contains 154 of water. a 15.0 piece of iron density 7.86 and a 18.0 piece of lead are added.
As was mentioned the one-way bandwidth available to a : as was mentioned the one-way bandwidth available to a single operator in the amps system is 12.5 mhz with a channel
When 560 g calcium and 347 g nitrogen gas undergo a : when 56.0 g calcium and 34.7 g nitrogen gas undergo a reaction that has a 88.0 yield what mass of calcium nitride
Compute the molar mass of vitamin c if a solution of 227 g : compute the molar mass of vitamin c if a solution of 22.7 g in 100. g of water freezes at -2.40 oc. the kf of water is
The vapor pressure of chlorine dioxide clo2 : the vapor pressure of chlorine dioxide clo2 is155torrat-22.75 ? cand485torrat 0?c. what is the normal boiling point of
Code for implementing a findbitplanes function to return : code for implementing a findbitplanes function to return any of the 8 bit plane images of the grayscale input

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Derive the state diagram for fsm that has input and output

Derive the state diagram for an FSM that has an input w and an output z. The machine has to generate z = 1 when the previous four values of w were 1001 or 1111; otherwise, z = 0. Overlapping input patterns are allowed.

  Find the laplace transform

Determine the Laplace transform of f(t) = +5e^-4t + 12sin 3t. If the voltage across a 2 F capacitor is initially zero, what is the instantaneous power if the current is A?

  At what speed does the motor spin

A stepper motor has 24 North teeth and 24 South teeth. What angle change occurs on each step If a full step is output every 1 ms (and assuming it doesn%u2019t slip), at what speed does the motor spin

  Determine difference equation relating input and output

Determine the I/O difference equation relating the input x(n) and the output y(n) for the following LTI systems with the impulse response: h(n)=(0.4)u(n)+(-0.4)^n u(n), where u(n) is the unit step sample signal

  Would it be preferable to put filter before noise amplifer

A filter with a great deal of attenuation must be placed in an amplifier chain. Ignoring all considerations other than the desire to minimize noise figure, would it be preferable to put the filter before or after a low noise amplifier Why

  How to connect both circuits to a 25k ohm load resistor

a. Given a circuit with a VCVS (A=1000) in series with a 100K ohm resistor, convert this circuit to a VCCS  in parallel with a resistor R. b. Connect both circuits to a 25K ohm load resistor and show they produce the same behavior in the load resis..

  How much electrical charge is needed to raise isolated metal

How much electrical charge is needed to raise an isolated metal sphere of radius 1.0 m to a potential of 1x10-6 V

  Determine the value of xl in a parallel resonant circuit

how do you determine the value of Xl in a parallel resonant circuit, when all youre given is Xc, Rcoil, and the parallel resistance

  Calculate the angle at the maximum instantaneous current

A purely inductive load of 10 ohms is connected to an ac source of 120 V (rms) through a half wave SCR circuit. a. If the SCR is triggered at 90 degrees, calculate the angle at the maximum instantaneous current.

  Derive a suitable sequential circuit

A sequential circuit has two inputs w 1 and w 2 , and an output, z. Derive a suitable circuit for the given condition.

  Youve just been hired as a process engineer at a major

youve just been hired as a process engineer at a major silicon chip manufacturer and your boss gives you a first

  Define what is the channel capacity for a channel

What is the channel capacity for a channel with a 300 Hz bandwidth and as S/N = 3? 2nd problem: Given a channel with a 50 kHz bandwidth and a S/N = 127, determine:

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd