Estimate the so2 concentration at midnight

Assignment Help Civil Engineering
Reference no: EM13543449

Consider a box model for an air shed over a city that is 1 X 105 m on a side, with a height of 1200 m induced by a temperature inversion. Winds with no SO2 blow at 4 m/s agains one side of the box. SO2 is emitted in the box at the rate of 20 kg/s.

(a) If SO2 is considered conservative, estimate the steady state concentration in the airshed.

(b) Assuming that SO2 emissions only occur on weekdays. If emission stop at 5 pm on Friday, estimate the SO2 concentration at midnight.

(c) If SO2 emissions begin again on Monday morning at 8 am, what would the concentration be by 5 pm?

Reference no: EM13543449

Questions Cloud

Calculate the friction head loss per meter of pipe : When fluid of specific weight 8.2 KN/m^3 flows in a 150-mm-diameter pipe, the frictional stress between the fluid and the pipe wall is 25 N/m^2. Calculate the friction head loss per meter of pipe. If the flow rate is 42 L/s, how much power is lose pe..
What is the exit pressure p2 if the friction head loss : Water ?ows at 6 ft/ s through a pipe 500 ft long with diameter 1 in. The inlet pressure p1= 200 psig, and the exit section is 100 ft ft higher than the inlet. What is the exit pressure p2 if the friction head loss is 350 ft?
Determine accelaration period in time : The 500- bed Lotta Hart Hospital has a small activated sludge plant to treat its wastewater. The average daily hospital discharge is 1200 L/day per bed
Determine the surface area of a primary settling tank sized : Determine the surface area of a primary settling tank sized to be handle a maximum hourly flow of 0.570 m3/s at an overflow rate of 60 m/day.If the effective tank depth is 3.0 m,what is the effective theoretical detention time?
Estimate the so2 concentration at midnight : Consider a box model for an air shed over a city that is 1 X 105 m on a side, with a height of 1200 m induced by a temperature inversion. Winds with no SO2 blow at 4 m/s agains one side of the box. SO2 is emitted in the box at the rate of 20 kg/s.
What is the effective theoretical detention time : Determine the surface area of a primary settling tank sized to be handle a maximum hourly flow of 0.570 m3/s at an overflow rate of 60 m/day.If the effective tank depth is 3.0 m,what is the effective theoretical detention time?
Calculate the position of the loop as the end of the whip : Assuming the mass of the whip is uniformly distributed along its length, calculate the velocity of the end of the whip as a function of the position of the loop (x), and calculate the position of the loop as the end of the whip breaks the speed of so..
Determine flow rate in a series pipe system given that rough : A sample of moist soil has a volume of 40.5 cc mass weight of 59.2 gms. After drying it has a mass weight of 48.3 grams. The specific gravity of the solids are 2.68. Compute the degree of saturation, water content and void ratio.
Revolve the pavement about its inside edge : Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the final specific volume of the system

A closed system of 0.123kg undergoes a frictionless, quasi-static process along the path PV=C from 100kpa to a final state where the volume is twice the initial volume.

  What measurements should be laid out to establish a distance

a tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. what measurements should be laid out to establish a horizontal distance of 682.25ft

  Explain the rule to solve the moment through the reactions

When using singularity functions, if I have a reactionary moment at a cantilever connection, do I use the right hand rule to solve the moment and determine it's direction through the reactions

  Determine the pressure variation in the flow field

A plane flow field is developed by addition of a free vortex and a uniform stream in the positive x direction. If the vortex is located a distance a from the origin, find the pressure variation in the flow field.

  Compute the difference in design curve lenghts for designs

The curve is to be redesigned for a 70 mph design speed in the year of 2025. Vehicle braking technology has advanced so that the recommended design deceleration rate is 25% greater that the 2011 value used to develop

  Determine the amount of air that must be bled off to restore

When the air temperature is 25°C, the pressure gage reads 210 kPa. If the volume of the tire is 0.025 m3, determine the pressure rise in the tire when the air temperature in the tire rises to 50°C.

  Determine the modulus of elasticity and the poison ratio

A tensile load of 50 000 lb is applied to a metal bar with a 0.6x0.6 in cross section and a gage length of 2 in. Under this load the bar elastically deforms so that the gae length increases to 2.007 in

  Determine normal stresses induced in steel and in concrete

The concrete post (Ec=3.6*10^6 psi and Ac= 5.5*10^-6/degrees F) is reinforced with six steel bars. each of 7/8-in diameter (Es=29*10^6 psi and As=6.5*10-6/ degrees F).

  At what depth of flow does the vehicle begin to move

You are in charge of evaluating the safety (hazard) of a low water crossing. Traffic surveys show that the "Aaverage"vehicle using the crossing is semi-rectangular in shape (10 ft long, 5 ft wide, and 4.0 ft high - not including the distance from the..

  Determine the rotational speed of the rollers

The distance from the center of the plate to the point of contact between the plate and the roller is 12 cm. The radius of the roller is 0.5 cm. Assuming no slip between the wheels and the plate, determine the rotational speed of the rollers.

  Determine the neutral axis angle given x and y deflection

determine the neutral axis angle given x and y deflection measurements and load applied (mm)

  Determine the power produced by the turbine

A Rankine cycle has a boiler pressure of 2500 psi and a condenser pressure of 1psi. The temperature at the inlet of the turbine is 800F. The turbine has an isentropic efficiency of 90 percent and the pump operates isentropically.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd