Determine what is the magnitude of the maximum stress

Assignment Help Civil Engineering
Reference no: EM13326398

What is the magnitude of the maximum stress that exists at the tip of an internal crack having a radius of curvature of 5.5× 10-4 mm (2.165 ×10-5 in.) and a crack length of 3.5 ×10-2 mm (1.378 × 10-3in.) when a tensile stress of 200 MPa(29010 psi) is applied?

Reference no: EM13326398

Questions Cloud

Determine what is demand for time if left turns are provided : Given the following geometry of an intersection: Four lanes fornorth and southbound traffic; two lanes for east and west boundtraffic. The peak hour volume for: northbound traffic is 1400vehicles with 10% left and right turns,
Determine what are the horizontal distances with an edm : The slope distances shown were measured with an EDM while the differences in elevation between the ends of each line were determined by leveling. What are the horizontal distances
Estimate the magnitude of the net force : A 3.00-kg mass undergoes an acceleration given by a = (2i+5j ) m/s2. The magnitude of the net force is
Estimate theoretical fracture strength of a brittle material : Estimate the theoretical fracture strength of a brittle material ifit is known that fracture occurs by the propagation of anelliptically shaped surface crack of length 0.2 mm(0.007874 in)
Determine what is the magnitude of the maximum stress : What is the magnitude of the maximum stress that exists at the tip of an internal crack having a radius of curvature of 5.5× 10-4 mm (2.165 ×10-5 in.) and a crack length of 3.5 ×10-2 mm (1.378 × 10-3in.)
Determine what is the oil flowrate in stb per day : Two wells had been drilled on 40-acre spacing. Well 1 is injectionand Well 2 is producing well. Down hole injection pressure is 8500psi, and bottom hole pressure in producing well is 2400 psi.
Find the electric filed at the common cetner of semicircles : two semicircular filament have a common diameter. one lies in the x-y plane and one in the x-z plane. the curved portion of each carries a uniform line charge density (rho). find the electric filed at the common cetner of the semicircles
Determine how many buses leave the terminal daily : A bus line 4 miles long runs through an area with 1/6 acre lots,3.5 people per household, average 1 car per household. People will walk up to 1/6 mile to a bus stop, so stops are located 1/3 mileapart along the route.
How mint countries become next global economic powerhouses : Discuss how the MINT countries can become the next global economic powerhouses.

Reviews

Write a Review

Civil Engineering Questions & Answers

  How would friction factor and pressure change be affected

Water at 20ºC flows at a velocity of 2 m/s in a 200-mm diameter horizontal ductile-iron pipe. a) Estimate the friction factor in the pipe, and state whether the pipe is hydraulically smooth or rough

  Find entropy changes of refrigerant and thermal reservoir

A thermal reservoir (T=308K) is brought in contact with the tank, transferring enough heat to the tank to raise the pressure inside to 4 bar. Calculate the entropy changes of the refrigerant and the thermal reservoir

  What is the current draw of the motor during the operation

The motor has an efficiency of 80%. It operates at 240V AC. A 12" diameter drum is attached to the gearbox output shaft, and a wire rope is wrapped around the drum to act as a winch. The winch is used to raise bucket of raw material in a factory.

  Determine the flow rate per unit width of aquifer

The aquifer is inhomogeneous with K = 12+0.006x, where x =0 at point 1, and the piezometric heads at point 1 and 2 are 14.2 m and 18.8 m, respectively measured above the upper confining layer.

  Maximum rod diameter on lathe machine

If the tensil testing machine can apply no more than 925 lbs. of force to the specimen, calculate the maximum rod diameter that should be used. (precision 0.000)?

  What is the estimated uncertainty in the length of vector

The base line vector between the base and roving reciever is 8340m and has an accuracy of +/-(1to 2 cm +/-2ppm). What is the estimated uncertainty in the length of this vector

  Determine the modulus of elasticity and the poissons ratio

Under this load the bar elastically deforms so that the gae length increases to 2.007 in. and the cross section decreases to 0.599x0.599 in. Determine the modulus of elasticity and the poisson's ratio for this metal.

  Find the mole fraction and mass fraction of each component

The output takes the form of a series of peaks where each peak corresponds to a component and a peak area (A) is proportional to the moles (n) of the component ( n = kA) in the sample injected in the GC.

  What is porportion of potential energy head at crosssection

if a pipeline is horizontal, what is the porportion of the potential energy head at the upstream crossection that is changed to kinetic energy head at the downstream crossesction

  Determine the velocity of the box 2 seconds later

A 20 kg box is on an upward inclined surface of 30 degrees from the floor. the velocity of the box is zero when it is subjected to a constant horizontal force F=30N. assuming the surface is smooth,

  Freeways density and level of service

What will the freeway's density and level of service be before and after the ban? (Assume that the trucks are removed and all other traffic attributes are unchanged).

  Provide a diagram showing the cost of the truss as function

A project for constructing a Facility just started. It involves the excavation of 40 to 60 feet deep and 60 feet wide trench to house double tunnels. A 24-inch outside diameter (22.5-inch inside diamater) water line is located in the path of the t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd