Determine the normal stress in each rod. show all work

Assignment Help Civil Engineering
Reference no: EM13543437

Two steel rods with fixed supports at A and C are attached by a rigid flange at point B and a downward load of 120 kN is applied to the flange. The upper rod has a cross section of 800 mm^2 and the lower rod has a cross section fo 1,600 mm^2. If the modulus of elasticity is 200 GPa determine the normal stress in each rod. Show all work.

Reference no: EM13543437

Previous Q& A

  Determine the minimum diameter shaft that can be used

The electric motor at A exerts a torque of 800N.m on the steel shaft from A to D. This has a torque of -300N.m at B and -500N.m at C. the dimensions are

  Why does a design engineer need to know the location of the

Course Ab of a five sided traverse runs due north. From the giben balanced interior angles to the right, compute and tabulate the bearings and azimuths from north for each side of the traverses.

  What is the left turn adjustment factor for the case describ

An intersection approach has three lanes, permitted left turns, and 6% left-turning volume with a through vehicle equivalent of 5.0 tvu/left turn. The saturation flow rate for through vehicles under prevailing conditions is 1,700 veh/hg/ln.

  Determine the vertical deflection at c

The bent road has an E=200 GPa, G=75 GPa, and a radius of 30 mm. Use Castigliano's theorem and determine the vertical deflection at C. Include the effects of bending, shear, and torsional strain energy.

  Determine the power that must be supplied to the pump at

Crude oil flows through a level section of the Alaskan pipeline at a rate of 1.6 million barrels per day (1 barrels=42 US gallons) the pipe inside diameter is 48 inch and its roughness is equivalent to galvanized iron.

  What is the flow rate of air that must be entering the hood

We have a situation where hydrogen gas at 300 degrees C is flowing out of a tube at the rate of 100 mL/min. The tube is located in a fume hood operating at 25 degrees C and 1 atm.

  Calculate the potential methane production in one year for

A 9,000-lb single wheel load is placed on a PCC slab that is 9.5 in. thick. The concrete has a modulus of elasticity of 5 million psi with a Poisson’s ratio of 0.15. The modulus of subgrade reaction is 225 pci. Tire pressure is 90 psi.

  Calculate the coefficient of volume compressibility

In an oedometer test, the void ratio of a clay sample changed from 1.62 to 1.41 as the vertical effective stress imposed on the sample was increased from 100 kPa to 200 kPa. Later on, the vertical effective stress on the sample was decreased

  How many rapid sand filter boxes of dimensions 10 m 10 m

A streamlined, high-speed train travels at 200 km/hr. The flow over the train is similar to flow over a flat plate. Estimate the boundary layer thickness at the end of the train, which is 125 m long. The temperature is 10°C.

  Calculate the over consolidation ratio of the clay layer

From the results of an oedometer test on an undisturbed sample of clay taken at a depth of 10 m from the ground surface, the maximum vertical preconsolidation pressure (s’vmax or s’c) was found to be 560 kPa. The clay layer has a saturated unit weigh..

Reviews

Write a Review

 

Similar Q& A

  Determine by analysis which of the cable a or b has tension

A body with a mass of 250 kg is supported by the flexible cable system. Determine by analysis which of the cable A, B, C, or D has the largest tension.

  Determine the settlements

Determine the settlements when a stress of 100 kPa is applied by the building over an area of 10m × 5 m on the soil surface.

  A rectangular beam made using concrete with fc 6000 psi

a rectangular beam made using concrete with fc 6000 psi and steel with fy60000 psi has a width b 20 in. the concrete

  How high did the ball roll before it momentarily stopped

A solid ball starts to roll up a hill with an initial velocity of 50m/s. The ball has a mass of 20 Kg with a 0.75 m radius. How high did the ball roll before it momentarily stopped

  Find magnitude of ground displacement and energy released

An earthquake with a magnitude 6.5 on the Richter scale is producing a ground displacement of 50 mm at a particular location and the energy released by the earthquake is "E".

  Find the load p and stress in the aluminum for the stress

The column is composed of two materials, the inner is brass with a diameter of 100mm and the outer is aluminum with a diameter of 150mm. A rigid flat plate is placed on top to insure that both materials move together when compressed.

  Find the magnitude and direction of the force

Find the magnitude and direction of the force the cable exerts on the pin for the pulleys

  1 draw a plan of a typical strip mine showing all

1. draw a plan of a typical strip mine showing all operational features and equipment.2. answer the followinga. why is

  What is the minimum energy necessary to compress vapor

What is the minimum energy necessary (in kJ) to compress 1.0 kg of saturated water vapor at 1 bar to a pressure of 60 bar in a perfectly insulated vessel

  Discuss all the factors that the client should consider

A flocculation/sedimentation combination basin in a conventional drinking water treatment plant is to be constructed of cast-in-place reinforced concrete. The horizontal flow rectangular basin will be located in New Jersey, USA.

  Determine entropy change of air during compression process

Air is compressed from an initial state of 100 kpa and 170 *C to a final state of 600 kpa and 57 *c. Determine the entropy change of air during the compression process by using a) property values from the air table and b) average specific heats

  Determine the forces acting on member bh

A bag of potatoes is sitting on the chair. The force exerted by the potatoes on the frame at one side of the chair is equivalent to horizontal and vertical forces of 24 N and 84 N, respectively, at E and a force of 28 N perpendicular to member BH ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd