Configuring bgp routing

Assignment Help Basic Computer Science
Reference no: EM131339371

Lab: Configuring BGP Routing

Objective

The overall objective of this lab is to configure BGP routing between two routers so that there is a routed BGP network connection between computers in the two LANs. You configure the network topology and the IP addresses for the appropriate router interfaces. This requires that the serial connection between routers be configured and enabled.

Topology

Figure 1: The Network Topology for This Lab

Key Concepts

The following concepts, terms, commands, and steps should be mastered in this laboratory exercise.

1. How do you configure BGP routing?

2. How can you assign the AS number?

3. What are the steps to configure the neighbor IP address and remote-as 65001?

4. How can you advertise the network to its BGP peers?

5. Examine the use of the show ip bgp sum command.

Reference Tables

For convenience, Table 1 provides the IP address and mask of all necessary interfaces used to complete the lab.

Table 1: The Computer IP Addresses, Subnet Masks, and Gateway Addresses for Lab 9

Computer/Interface - R1

IP Address

Subnet Mask

Gateway Address

   PC1

10.10.12.1

255.255.255.0

10.10.12.250

R1-Fa0/0

10.10.12.250

255.255.255.0

     ------------------

R1-S0/0/0

172.16.25.1

255.255.255.252

     ------------------

Computer/Interface - R2

IP Address

Subnet Mask

Gateway Address

   PC2

10.10.30.65

255.255.255.0

10.10.30.250

R2-Fa0/0

10.10.30.250

255.255.255.0

     ------------------

R2-S0/0/1

172.16.25.2

255.255.255.252

     ------------------

Detailed Lab Steps

In the following tasks, you must demonstrate your knowledge to configure computer networks. Each task specifies a particular network setting you are required to input. You are required to document the command(s) used to accomplish each task.

Task # 1 

In this lab, you configure BGP from the Customer-Router to the ISP Router [Router-ISP] based on the network topology provided in Figure 1. You use the IP addresses provided in Table 1. You will be asked to verify that computers in your LAN can ping the neighbor LAN. You are configuring BGP routing for 10.10.12.0/24, 10.10.30.0/24, and 172.16.25.0/30 networks. Note that a serial interface is used to interconnect the LANs. Use 56000 for the clock rate on the serial link (DCE interface). The enable secret and line console 0 password should be set to ciscopress.

1. Configure the gateway address for your LAN routers according to the addresses listed in Table 1. List the prompt and the command used to configure the gateway address and subnet mask on each of the routers.

2. Configure the hostname for your routers; R1 should be renamed the Customer-Router and R2 should be renamed Router-ISP. List the router prompt and command used to configure the router's hostname.

3. Enable BGP routing on the Customer-router using an AS number of 65000. Advertise the 10.10.12.0 network to its BGP peers. Use the command to specify the IP address of the BGP neighbor. Use the command to specify this is the ISP BGP Connection.

4. Enable BGP routing on Router-ISP using an AS number of 65001. Advertise the 10.10.30.0 network to its BGP peers. Use the command to specify the IP address of the BGP neighbor. Use the command to specify this is the Customer BGP Connection.

5. Use the ping command to verify that you have the customer ping the ISP using the IP address provided by the ISP.

Reference no: EM131339371

The requirements are accurate and correct

Discuss the following questions with your classmates in the Class Discussion section: What does it mean to have integrated requirements models? How should they be used? Each o

Sort the array and write out the sorted array

Consider a program that will read employee information into an array of objects, sort the array by employee identification number, write out the sorted array, and compute v

Write a program to simulate for a given value of ?

Find the minimum value of the contention interval. Note that you will have to find one attempt past the one that succeeds, in order to determine if there was a collision. Ig

What are different types of memory

What are some of the newer technology innovations you have seen in regards to I/O and Memory? What are the different types of Memory and how much is recommended?

Minimum circuit of two-input and and two-input

For the function F(A, B, C, D, E) = ∑m(0, 1, 2, 3, 4, 5, 7, 9, 11, 13, 14, 15): a. Find a minimum circuit of two-input AND and two-input OR gates to realize F. Attach a Word

Multiplexors whose control bit allows

Multiplexors whose control bit allows you to select between one of two modes right shift or left shift. Include logic to perform arithmetic shift left and arithmetic shift

Write a program to measure latency of communication

If you have access to an SMP and a cluster, write a program to measure latency of communication and bandwidth of communication between processors, as was plotted in Figure F

Needed amount to purchase the boat

Carrie would like to buy a boat that costs $14,300. She currently has $12,500 saved up and intends on investing this amount in an account that earns 8.5% simple interest. Ho

Reviews

Write a Review

 
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd