Combined cycle power plant burns natural gas

Assignment Help Mechanical Engineering
Reference no: EM13710324

A combined cycle power plant burns natural gas and produces 600MW and has an efficiency of 48%. Find the whole sale cost of natural gas and determine the cost of the fuel burned per second for the plant to produce it rated output of 600MW

Reference no: EM13710324

Questions Cloud

Demonstrate how the project will be completed : Develop a list of project tasks and the dates for completion to demonstrate how the project will be completed within the semester - Provide an overview of the main points to be covered in the report and a concise outline of the paper content and str..
What was the mass of hot water withdrawn from the tank : Hot water is provided to a house by an electric water heater which uses a 60L tank. The electric heater is rated for a 1.6kW. The hot water tank is completely full with water at 80°C when someone starts a shower. The shower faucet mixes cold water at..
Air flows steadily through a one-inlet : Air flows steadily through a one-inlet, one-exit control volume. At the inlet, which has a flow area of 28 cm2, the air is at 600 kPa, 500 K, and has velocity of 30 m/s. At the exit, the pressure is 300 kPa, the temperature is 456.5 K, and the veloci..
Estimate the power required to maintain cylinder temperature : A heated cylinder, 0.0635 m long and 0.0127 m diameter, is exposed to an air stream in cross flow arrangement having air speed of 10.5 m/sec. If the cylinder surface temperature is 50 C and the air temperature is 22 C, estimate the power required to ..
Combined cycle power plant burns natural gas : A combined cycle power plant burns natural gas and produces 600MW and has an efficiency of 48%. Find the whole sale cost of natural gas and determine the cost of the fuel burned per second for the plant to produce it rated output of 600MW
Steam heated at constant pressure in a steam generator : Steam heated at constant pressure in a steam generator enters the first stage of a supercritical reheat cycle at 28 MPa, 520°C. Steam exiting the first-stage turbine at 6 MPa is reheated at constant pressure to 500°C. Each turbine stage has an isentr..
Adiabatic heat exchanger is used to heat cold water : An adiabatic heat exchanger is used to heat cold water at 8°C entering at a rate of 3 kg/s using hot air at 150°C entering with the same mass flow rate. If the air’s exit temperature air is 30°C,
Flow of clockwise vortex of circulation gamma : Consider the flow of clockwise vortex of circulation gamma and a source of strength Q, both located at the origin. Show that the result is a spiral flow in which the velocity is everywhere inclined at the same angle to the radius vector from the orig..
Promising method of power generation involves collecting : A promising method of power generation involves collecting and storing solar energy in large artificial lakes a few meters deep, called solar ponds. Solar energy is absorbed by all parts of the pond, and the water temperature rises everywhere. The to..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assume the regriderator works in a carnot cycle between -10

a refridgerator should remove 500 kj from some food. assume the regriderator works in a carnot cycle between -10 and 45

  Determine the smallest horizontal force required to pull

determine the smallest horizontal force required to pull out wedge a. the crate has a weight of 200 and the coefficient

  A concrete pipe with an inside and outside diameter of 60

a concrete pipe with an inside and outside diameter of 60 cm and 70 cm respectively hangs from cables. the pipe is

  The position of a particle one straight line

The position of a particle one straight line is s=2t^2-12t5 (ft), where t is in seconds.

  What are the required mass fractions of the carbon fiber

An epoxy matrix composite containing both HS (such as T-300) carbon fiber and E-glass fiber is to be formulated such that the cost/ kg is to be equal $ 8.00/ kg. It is desired to keep the total fiber volume fractionequal to 60 %. What are the requ..

  The roller-coaster track shown is contained in a vertical

the roller-coaster track shown is contained in a vertical plane. the portion of track between a and b is straight and

  A boat of length 50 m is designed to cruise at 30 mph and

a boat of length 50 m is designed to cruise at 30 mph and is to be tested in a tow tank with a model of length 0.5 m.

  The currently used material is brass but you have decided

you are asked to design a solid circular shaft of minimum cost that is 1.3 m long and has to twist less than 3 degrees

  Determine the work and heat transfer involved in the

one kilogram of water initially at 200 degc and 0.2 mpa undergoes an isothermal internally reversible compression

  Find out the coefficients m and b of the function you

below is measured voltage v at different time stimes 0 0.5 1 1.5 2 2.5

  The collector transfers heat by natural convection to the

a flat plate solar collector 6 ft by 12 ft is mounted on the roof of a house. the outer surface of the collector is at

  A 25 mm diameter uniform steel shaft is 600 mm long between

a 25 mm diameter uniform steel shaft is 600 mm long between bearings.a find the lowest critical speed of the shaftb if

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd