Find out the coefficients m and b of the function you

Assignment Help Mechanical Engineering
Reference no: EM13631214

Below is measured voltage (V) at different time (s)

Time(s) 0 0.5 1 1.5 2 2.5 3 3.5

Voltage (V) 100 62 38 21 13 7 4 2

(1) Plot linear function, power fuction and exponential fuction against these data. Plot both data points (with 'o') and fuction line ('-') on the same plot. keep the three plots on the same plot. (use subplot). Decide which function best fits these data.

(2) find out the coefficients m and b of the function you decided from (1) and plot the original data with this function on the same plot.

Reference no: EM13631214

Questions Cloud

Plot the first order polynomial second order polynomian and : below is pressure measured at different timetime
A photograph of this zone plate is to be reduced on : a fresnel zone plate is prepared with a drawing program and printed on a laser printer. the printed zone plate has a
A 50 w light bulb shines through two polarizers after : a 50 w light bulb shines through two polarizers. after having passed through the first polarizer the electric field
An ideal regenerative steam power cycle operates so that : an ideal regenerative steam power cycle operates so that steam enters the turbine at 30 bars and 500 degrees celcius
Find out the coefficients m and b of the function you : below is measured voltage v at different time stimes 0 0.5 1 1.5 2 2.5
The displacement function ux for a tensile specimen of : the displacement function ux for a tensile specimen of uniform cross section and length l fixed at one end and
Blood flows in an aorta of radius 425mm at 350cms calculate : 1. blood flows in an aorta of radius 4.25mm at 35.0cms. calculate the volume flow rate.2. although the cross-sectional
An ideal diesel cycle with air as the working fluid has a : an ideal diesel cycle with air as the working fluid has a compression ratio of 22 and a cutoff ratio of 2.5. at the
Assume that the funding can be set aside in an account that : a new dam project will require 48000 a year in maintenance costs after it is complete. these maintenance costs will

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

  Determine the magnitude of its acceleration

The car travels up the hill with a speed of v = (0.4s) m/s, where s is in meters, measured from A. Determine the magnitude of its acceleration when it is at point s = 50 m, where p = 500 m.

  Determine isentropic efficiency of the compressor

Carbon dioxide enters an adiabatic compressor at 100kPa and 300K at a rate of 0.5kg/s and exits at 600kPa and 450K. Considering constant specific heat, determine (a) isentropic efficiency of the compressor (b) the rate of entropy change in (kW/K) ..

  Consider a naca 0009 airfoil that has a plain flap whose

consider a naca 0009 airfoil that has a plain flap whose length is 0.2c and which is deflected 25. a. calculate cl and

  Why is it easier to exhale than to inhale in order to blow

why is it easier to exhale than to inhale in order to blow out a candle? how is it related to laminar flow or steady

  Evaluate thermal efficiency of the cycle

Evaluate thermal efficiency of the cycle

  Calculate the convective heat transfer coefficient

air at a pressure of 200 kpa and free stream temperature of 27 degc flows over a square plate at a velocity of 30 ms.

  What is the maximum load that may be applied to a specimen

for a brass alloy the stress at which plastic deformation begins is 345 mpa 50000 psi and the modulus of elasticity is

  Determine the final temperature in the tank the mass of

a 0.4m3 rigid tank initially contains refrigerant-134a at 14 degree c. at this state 70 of the mass is in the vapour

  A carnot refrigerator is maintaining food stuffs in a

a carnot refrigerator is maintaining food stuffs in a refrigerated area at 2oc by rejecting heat to the atmosphere at

  A projectile is fired with an initial speed of 633msat an

a projectile is fired with an initial speed of 63.3msat an angle of 43.7circ above the horizontal on a long flat firing

  Calculate the necessary piston displacement in order to

a 3-diameter 5-long gas-piston assembly contains air at stp. stp standard temperature and pressure conditions 300k and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd