Calculate the range of frequencies

Assignment Help Mechanical Engineering
Reference no: EM131143963

A 3000-kg machine tool exhibits a large resonance at 120 Hz. The plant manager attaches an absorber to the machine of 600 kg tuned to 120 Hz.

Calculate the range of frequencies at which the amplitude of the machine vibration is less with the absorber fitted than without the absorber.

Reference no: EM131143963

Questions Cloud

Calculate the damping ratio required : Calculate the damping ratio required to limit the displacement transmissibility to 4 at resonance for any damped isolation system.
Determine the radius of curvature r : A W200 X 31.3 rolled-steel beam is subjected to a couple M of moment 45 kN.m. Knowing that E = 200 GPa and n = 0.29, determine
Determine the largest couple m that can be applied to a beam : (a) Using an allowable stress of 120 MPa, determine the largest couple M that can be applied to a beam of the cross section shown. (b) Solve part a, assuming that the cross section of the beam is an 80-mm square
Design a retrofit undamped absorber : Design a retrofit undamped absorber such that the nearest resonance is at least 20% away from the driving frequency.
Calculate the range of frequencies : Calculate the range of frequencies at which the amplitude of the machine vibration is less with the absorber fitted than without the absorber.
Rendering the system safe for operation : Redesign the absorber so that ω1 6 2000 rpm and ω2 7 4000 rpm, rendering the system safe for operation.
Calculate how much spoils the absorber design : Calculate how much spoils the absorber design by determining the magnitude X using equation (5.32).
Prepare a recommendation : prepare a recommendation. - In recommendation, you will want to have a table showing the payback period, accounting rate of return, net present value, and internal rate of return for each proposal.
Determine the maximum stress in a coiled rod : Straight rods of 6-mm diameter and 30-m length are stored by coiling the rods inside a drum of 1.25-m inside diameter. Assuming that the yield strength is not exceeded

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Principles of project management

Explain the principles of project management with particular emphasis on:

  Calculate the heat lost per square meter area of the furnace

Calculate the heat lost per square meter area of the furnace wall and also find outside surface temperature.

  The piston is initially resting on the stops the cylinder

the piston is initially resting on the stops . the cylinder contains carbon dioxide at 50 psia and 200 f and takes up 1

  What will be the maximum output power

Why is this lab exercise useful? Where can the results be used in engi-neering design/industry - Prom your experimental setup what will be the maximum output power?

  Determine the modulus of elasticity

For a logarithmic stress strain curve and find the strength coefficient and strain hardening exponent. Determine the modulus of elasticity. Determine the toughness.

  What is the heat exchanger effectiveness

What is the maximum possible heat transfer rate? What is the heat exchanger effectiveness? Should the heat exchanger be operated in parallel flow or in coun- terflow? What is the ratio of the required areas for these two flow conditions?

  Find the size of the sample required to estimate the mean

suppose that the minimum and maximum ages for typical textbooks currently used in college courses are 2 and 8 years.

  Initially the pressure and volume of the gas is 200 kpa and

a gas behaves such that the product of its pressure and volume is constant pvc. initially the pressure and volume of

  Determine the minimum force p to get to move and if the

a 2 m long concrete traffic barrier is used to provide safety during highway construction. if h45 cm determine the

  Determine the radial and tangential stress distributions

A steel flywheel 25 mm thick with an outer diameter of 1 m and an inner diameter of 200mm is rotating at 100 hz. Determine the radial and tangential stress distributions as a function of radial position r. Plot the distribution

  Determine the required mass flow rate of air for a net

air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 10 a compressor inlet

  If the company used an interest rate of 12 per year in

the effort required to maintain a scanning electron microscope is known to increase by a fixed percentage each year. a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd