Thermodynamic Project, Mechanical Engineering

Assignment Help:
ES 347 - Thermodynamics Project Assigned: 3/28/2013 Due: 4/25/2013
Problem specification
5 kg of air is contained in a piston-cylinder device, initially at a pressure of 2MPa and a specific volume of 0.08m3/kg. The air then expands, as an ideal gas, through a polytropic process, with variable values of n, to a final specific volume of 0.30m3/kg.
Objective:
Write a MATLAB code to solve for the pressure and temperature variation throughout the expansion process and to calculate the work and heat produced in the processes for variable values of n.
Procedure: 1. Begin by defining the temperature at the initial state and then define the temperature and
pressure at the final state. Sketch a rough graph of what the process looks like on P-v coordinates. Write out by hand the equations and steps you would take to determine the actual P, T, and v at all points along the process. Identify unknowns, equations, constants, and calculation orders.
2. Using your hand calculations as a guide, write a simple MATLAB m-file to calculate the properties at points along the process (minimum of 20 points, but should be a variable that can be changed) using one of the values of n (I recommend using n=1.5). Plot P-v and T-v diagrams for the process using MATLAB.
3. Calculate the work performed for the process by integrating the curve of pressure versus specific volume. Use the “trapezoidal area method” for calculating the integral.
4. Assume that the specific internal energy for the air in this problem can be defined as a function of temperature as follows:
??(??) = (1.0344 * 10-4) * ??2 + (6.4476 * 10-1) * ?? + (1.3727 * 102)
Add code to your MATLAB program to calculate the specific internal energy for the process
using the information of the pressure and specific volume at each state. 5. Using conservation of energy and the work calculated, determine the amount of heat
transferred for each process. 6. Write a loop in the code to analyze the different values of n, or run the code for the different
values of n asked for below.
Deliverables 1. Hand calculations that outline planned MATLAB code. 2. MATLAB code (m-file) that calculates the state variables P, v, T, and u for the defined
process, and that calculates the work and heat for each process. 3. On the same graph, plot of P-v for this process with 4 different values of n: 1, 1.4, 1.5, 1.8. 4. Plot of P-v and T-v for n=1.5 on a single graph. Use the function plotyy. 5. Table summarizing results of work and heat as a function of n. 6. A brief paragraph detailing what you learned in this exercise and how useful you think these
skills will be for your future as an engineer. This is not a BS question, I want you to provide me with useful information about your experience. If you didn’t learn anything here because you already are a pro at MATLAB, say that!
For your reference, I have uploaded the m-file example_xy.m as an example of MATLAB programming and showing you some of the things you will need and can use.
I am happy to review any code problems you have, but I will not be checking code on the night before the due date, and it might take me a day or two to get to debugging any code that you send me. Therefore, plan ahead!
I will discuss the “trapezoidal area method” in class during the week of 4/1/2013.

Please follow the instructions

Related Discussions:- Thermodynamic Project

Gun fires - projectile motion, Gun fires - projectile motion: A gun fi...

Gun fires - projectile motion: A gun fires a projectile along with a muzzle velocity of 300 m/sec as illustrated in Figure. Find its angle of inclination so that it strikes a

Tank insulation process, Q. Tank Insulation process? With Owner's appro...

Q. Tank Insulation process? With Owner's approval, spray urethane foam may be used. Manufacturer's recommendations for service temperature limit shall be followed for specific

What are the types of interface, What are the Types of interface An int...

What are the Types of interface An interface can be regarded as an aggregate of conditions, rules and conventions which describes the information exchange, between two communic

Copper-beryllium alloys, Copper-Beryllium Alloys Copper-beryllium allo...

Copper-Beryllium Alloys Copper-beryllium alloys comprise between 0.6 to 2% Be and 0.2 to 2.5% Cobalt. Such alloys can be precipitation hardened and cold worked to improve a te

Briefly explain how geothermal powerplant operate, Illustrate types of nucl...

Illustrate types of nuclear reactors with diagrams? a) Give advantages and disadvantages of nuclear power plant? b) Briefly explain how geothermal powerplant operate with fig

Inspection and testing of vessels, Q. Inspection and testing of vessels? ...

Q. Inspection and testing of vessels? The Vendor shall be responsible for all inspection and testing. WorleyParsons reserves the right to inspect vessels or parts of vessels at

Hazardous waste and material standards, Hazardous Waste and Material Standa...

Hazardous Waste and Material Standards Each hazardous site must be examined and evaluated for its characteristics before workers are allowed entry. This will pre decide an

Consideration for centrifugal tension, Consideration: 1. From above eq...

Consideration: 1. From above equation, it is clear that centrifugal tension is not dependent of T1 and T2. It depends upon velocity of the belt. For lower belt speed (that is,

Make evaluation for the engine efficiency, (a) Differentiate between carnot...

(a) Differentiate between carnot Heat pump and carnot Heat engine. What is the basic cycle for a carnot Heat pump ? Explain it. (b) A reversible heat engine delivers 0.6 K at po

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd