Short-term measures for technical loss reduction, Electrical Engineering

Assignment Help:

Short-Term Measures for Technical Loss Reduction

The short-term measures involve measures needs for immediate improvement and reduction of losses within the system. These are based upon the information / data readily available along with the utilities. The works proposed under this plan should be based on the sample studies/statistical check/scrutiny of the existing system details.

Short-term Measures for Technical Loss Reduction

  1. Network Reconfiguration
  2. Network Reconductoring
  3. Preventing Leakages at Insulators
  4. Employing AVB (Automatic Voltage Booster)
  5. Distribution Transformers will managed better
  6. Load Balancing and Load Management
  7. Capacitor Installation (Series or Shunt)
  8. Improving Joints and Connections
  9. Laying Additional Link Lines
  10. Increase in HT:LT Ratio
  11. The High Voltage Distribution System Adoption (HVDS)
  12. Daily Maintenance of Distribution Network
  13. Creation of Primary Substation

A combination of one or more of the above measures would have to be taken to bring the losses down to acceptable levels.


Related Discussions:- Short-term measures for technical loss reduction

Explain what happen as the frequency increases, Question: (a) A typica...

Question: (a) A typical RF filter is made up of sections using circuit components. One example of a section is the Inductor-Capacitor (L-C) section. State two other types of

Analog-to-digital converters, Analog-to-Digital (A/D) Converters An A/D...

Analog-to-Digital (A/D) Converters An A/D converter converts analog input signals into digital output data in many areas such as process control, aircraft control, and telemetr

Use ideal op-amp technique to find voltage at point, Q. In the circuit show...

Q. In the circuit shown in Figure, use the ideal op-amp technique to find: (a) v o as a function of v i . (b) The voltage at A.

Basic features of electricity and circuit, 1.   Describe the basic featur...

1.   Describe the basic features of electricity at a fundamental level ? (to achieve a pass grade, explain the nature of electricity) 2.   What part of a cable are conduc

Determine the memory access time, Question: (a) Explain the types of ha...

Question: (a) Explain the types of hazards in a 5 stage pipeline. (b) Describe the three RAW dependencies in the following instructions. i: R7←R12+R15 i + 1: R8←R7-R1

Explain signal description of 8085, Explain signal description of 8085 ...

Explain signal description of 8085 a) Address bus b) Control and status signal c)  Address latch enable d)  S1,S0 status signals e)  Read ,write signal

Dual-ramp analog to digital converter, Q. Dual-ramp analog to digital conve...

Q. Dual-ramp analog to digital converter? Figure (a) shows the block diagram of a dual-ramp (dual-slope) A/D converter. After a start-of-conversion pulse, the counter is cleare

Find the open-circuit voltage amplification of the circuit, (a) Figure show...

(a) Figure shows a circuit containing an amplifier block. Find the open-circuit voltage amplification of the circuit. (b) Let the output terminals be connected to a load resista

Network theorems.., how to calculate voltage when 3 voltage sources are giv...

how to calculate voltage when 3 voltage sources are given?

Explain kirchhoff current law, Q. Explain Kirchhoff current law? The ba...

Q. Explain Kirchhoff current law? The basic laws that must be satisfied among circuit currents and circuit voltages are known as Kirchhoff 's current law (KCL) and Kirchhoff 's

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd