Satellite Communication, Electrical Engineering

Assignment Help:
ubmission Deadline: Wednesday, July 7, 2021
Assignment 2 EE5543 - Satellite Communication
Question 1: MEASAT-1 is located at 91.5
o E and operating at the base frequency of 10.982 GHz and
assumed to be a geostationary satellite (i.e. inclination is zero and in circular orbit). Assuming that
the difference in speed that is needed to change the semi major axis (from changes of energy) can be
approximated by Equation (1).
dv =
µ
2voa
2
0
× da (1)
• The initial semi-major axis a0?
• The initial velocity of the satellite?
• The initial Doppler shift?
• During station keeping, the satellite has drifted about 1.5
o Eastward in longitude, calculate the
velocity needed to re-track the satellite?
• The Doppler shift when the satellite was drifted?
Question 2: The semi-major axis of planet Mars is 227,939,100 km and the µsun is 1.327x1011km3/s2

Related Discussions:- Satellite Communication

Determine speed of the rotor field relative to rotor winding, Abalanced thr...

Abalanced three-phase, 60-Hz voltage is applied to a three-phase, two-pole induction motor. Corresponding to a per-unit slip of 0.05, determine the following: (a) The speed of t

Show maximum power transfer, Q. Show Maximum Power Transfer? In order t...

Q. Show Maximum Power Transfer? In order to investigate the power transfer between a practical source and a load connected to it, let us consider Figure , in which a constant v

Composition of fet, Composition of FET The FET (field-effect transisto...

Composition of FET The FET (field-effect transistor) can be constructed from several semiconductors, silicon being by far the most common. Several FETs are made with conventio

Determine the input current and input voltage, Q. A 100-kVA, 2300:230-V, 60...

Q. A 100-kVA, 2300:230-V, 60-Hz, single-phase transformer has the following parameters: R 1 = 0.30 , R 2 = 0.003 , RC 1 = 4.5k, X 1 = 0.65 , X 2 = 0.0065 , and Xm 1 = 1.

Discuss the operation of the jk flip-flop, Q. Figure shows the master-slave...

Q. Figure shows the master-slave JKFF. Assuming that the output changes on the falling edge of the clock pulse (i.e., when the clock pulse goes from high to low), discuss the opera

Compute the firing angle for the rated braking torque, Consider a 3-hp, 220...

Consider a 3-hp, 220-V, 1800-r/min separately excited dcmotor controlled by a single-phase fully controlled rectifierwith an ac source voltage of 230Vat 60Hz.Assume that the full-l

Explain inductorless filters, Q. Explain Inductorless Filters Inductorl...

Q. Explain Inductorless Filters Inductorless (Active) Filters Filters (used to pass or eliminate certain frequency components of a signal) that are suitable for IC fabricati

Add the contents of register - add instruction , Add the Contents of Regist...

Add the Contents of Register   This  instruction is used to add the contents  of register R with  the contents  of accumulator  and result  of operation is stored  in the accumu

Methods for speed and torque control of induction motors, Q. Methods for sp...

Q. Methods for speed and torque control of induction motors? The following are methods available for speed and torque control of induction motors. • Pole-changing method

Explain the block diagrtam of d.c. voltmeter , Q.   Explain the block diagr...

Q.   Explain the block diagrtam of D.C. voltmeter with direct coupled amplifier. Sol. D.C, voltmeter with direct coupled Amplifier         The D.C. electronic voltmeters

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd